Cisco Systems

ASA 7.2 & 8.0: disconnect PPPoE session

Hallo, we have setup a ASA v7.2 or v8.0 with a perfectly working PPPoE connection. I would like to disconnect the PPPoE...

0 comments posted 17yrs

posted by s.westi

0 comments posted 17yrs posted by s.westi

Internet Transit on MPLS Backbone ? what is the best solution ?

Hi i request your help for the choice of a solution. Actually, i have a backbone with 4 Cisco Catalyst 6500 MSFC2/PFC2...

0 comments posted 17yrs

posted by mag

0 comments posted 17yrs posted by mag

WLAN, VLAN & BVI

Hi There, I have a general question concerning BVI & Dot11 interfaces on a 871W. I had to configure a Subinterface for...

0 comments posted 17yrs

posted by aheinzelmann

0 comments posted 17yrs posted by aheinzelmann

Cisco Catalyst 6500 and VPLS ?

Hi anyone know if cisco catalyst 6500 with sup2/msfc2/pfc2 can support VPLS ? because i have: c6509-1#sh mpls l2transpo...

2 comments posted 17yrs

posted by mag

2 comments posted 17yrs posted by mag

Cisco 1721 SHDSL

I have a Cisco 1721 with a fasteth0 (10/100) Interface for LAN and and a eth0 (10BT) for WAN. Is it possible to program...

2 comments posted 17yrs

posted by b.vonken

2 comments posted 17yrs posted by b.vonken

cisco 7940 phone - create personal directory

I've got a few cisco 7940 phones working with cme 4.1 on a cisco 2600 router but I can't figure out how to create a per...

0 comments posted 17yrs

posted by tg

0 comments posted 17yrs posted by tg

CISCO Linksys WRT160N

Hi, I am using LINUX DD-WRT on a CISCO Linksys WRT160N have just started playing with the brctl command, which I am ass...

7 comments posted 17yrs

posted by Aaron Spiteri

7 comments posted 17yrs posted by Aaron Spiteri

Cisco 851/%SYS-2-MALLOCFAIL: Memory allocation of 65536 bytes failed

Hi, First time posting here. I have a new Cisco 851 router. Like clockwork, every 4 days I find the following in the SY...

3 comments posted 17yrs

posted by VAXman-

3 comments posted 17yrs posted by VAXman-

will 7961 phone work with cme 4.1?

1 comments posted 17yrs

posted by mickeymouse

1 comments posted 17yrs posted by mickeymouse

WAAS w/ WCCP not working

Hi everyone, We are having some problems putting WAAS (4.1.1b) with wccp to work on our network. I am going to try to d...

0 comments posted 17yrs

posted by francisco.sanches

0 comments posted 17yrs posted by francisco.sanches

Probleme with nm-16am v1.0

hello i have a cisco 3725 router with ios ipbase 12.3(9e) there are to nm-16am v1.0 card and a wic-1t connected the rou...

1 comments posted 17yrs

posted by liesbensaid

1 comments posted 17yrs posted by liesbensaid

NAT problem

We believe we have a NAT issue we need help with. In the configuration FastEthernet0/0 is on the internal network while...

6 comments posted 17yrs

posted by rsxh

6 comments posted 17yrs posted by rsxh

How to Configure RIP on Cisco 2950G-L3

I have a Cisco 2950G-L3 switch. It is configured for Integrated Routing and Bridging. I have it configured with several...

3 comments posted 17yrs

posted by naves.tom

3 comments posted 17yrs posted by naves.tom

Help needed on route-map

Hello I think that the correct topic should be route-map I need help about that: This is the scenario: Cisco 2650 with:...

0 comments posted 17yrs

posted by admin

0 comments posted 17yrs posted by admin

Vlan general Question

Hi there, I have a general question concerning VLANs: Is it possible to have more than one VLAN in one subnet? I remebe...

6 comments posted 17yrs

posted by aheinzelmann

6 comments posted 17yrs posted by aheinzelmann