Cisco 1841 and SDSL WIC Card


I have a CISCO 1841 router with a ADSL WIC in it. I decided to add a CISCO SDSL WIC in it. But I am unable to configure it from the IOS software as I cannot see it

Can any one point me in the right direction

here are the output from sh ver and sh diag

Clearly the diag can see it, but when I do show interface it does not show up, it only shows the ADSL interface

++++++++++++++++++++++++++++++++++++++++++++++++++++++ show diag Slot 0: C1841 2FE 2SLOT Mainboard Port adapter, 4 ports Port adapter is analyzed Port adapter insertion time unknown EEPROM contents at hardware discovery: Chassis MAC Address : 001d.71d7.ed64 MAC Address block size : 34 PCB Serial Number : FOC11364UZD Hardware Revision : 7.0 Part Number : 73-8191-08 Board Revision : C0 Top Assy. Part Number : 800-23434-06 Deviation Number : 0 Fab Version : 04 CLEI Code : IPM7W00CRA RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Product (FRU) Number : CISCO1841 Version Identifier : V05 Processor type : 86 Chassis Serial Number : FCZ114091K5 EEPROM format version 4 EEPROM contents (hex): ...


Hardware Revision : 0.0 Top Assy. Part Number : 800-26571-02 Board Revision : C0 Deviation Number : 0 Fab Version : 01 PCB Serial Number : FOC11473840 RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Version Identifier : V02 Product (FRU) Number : WIC-1SHDSL-V3 EEPROM format version 4


Hardware Revision : 2.3 Part Number : 73-4771-09 Board Revision : C0 Deviation Number : 0-0 Fab Version : 05 PCB Serial Number : FOC11355HRC RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Product (FRU) Number : WIC-1ADSL= EEPROM format version 4 ....

++++++++++++++++++++++++++++++++++++++++++++++++++++++ ++++++++++++++++++++++++++++++++++++++++++++++++++++++ show ver

Cisco IOS Software, 1841 Software (C1841-BROADBAND-M), Version

12.4(16a), RELEASE SOFTWARE (fc2) Technical Support:
formatting link
(c) 1986-2007 by Cisco Systems, Inc. Compiled Mon 10-Sep-07 07:24 by prod_rel_team

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

yourname uptime is 32 minutes System returned to ROM by power-on System image file is "flash:c1841-broadband-mz.124-16a.bin"

Cisco 1841 (revision 7.0) with 113664K/17408K bytes of memory. Processor board ID FCZ114091K5

1 DSL controller 2 FastEthernet interfaces 1 ATM interface DRAM configuration is 64 bits wide with parity disabled. 191K bytes of NVRAM. 31360K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

Reply to
Loading thread data ...

conf t controller dsl 0/0 line-term cpe mode atm line-mode ... ....

Looks like you have a DSL controller. You should be all set. After you do your controller dsl 0/0 commands, you should have an ATM 0/0 interface.

formatting link

Reply to
Doug McIntyre Forums website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.