Did you meen turn on ethernet Interface "no shutdown"?
Here is "show run" of router.
Router#sh run Building configuration...
Current configuration : 808 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot system flash flash:c3620-i-mz.123-16a.bin boot-end-marker ! ! memory-size iomem 10 no aaa new-model ip subnet-zero ! ! ip cef ! ! interface FastEthernet0/0 ip address 10.0.0.82 255.255.255.0 duplex auto speed auto ! interface Serial0/0 no ip address shutdown clock rate 2000000 no fair-queue ! interface FastEthernet0/1 no ip address shutdown duplex auto
interface BRI1/0 no ip address shutdown
! interface Ethernet1/0 no ip address shutdown half-duplex ! ip http server ip classless ! ! ! line con 0 line aux 0 line vty 0 4 login ! ! end
I read from internet that i must first boot IOS from flash and then from tftp, because IOS from flash set up interfaces, and then boot from tftp. I need command to first boot from flash then from tftp.
It is tru that 3600 must boot an image from flash first.
However what I would do is put a valid image as the first file in flash so that the system can find it but I would not put a boot command fro that image in the running-config/startup-config.
Router#sh ver Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3620-I-M), Version 12.3(16a), RELEASE SOFTWARE (fc2) Technical Support:
formatting link
(c) 1986-2005 by cisco Systems, Inc. Compiled Thu 10-Nov-05 03:19 by evmiller Image text-base: 0x60008B00, data-base: 0x60CE2000
ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (f c1) ROM: 3600 Software (C3620-I-M), Version 12.3(16a), RELEASE SOFTWARE (fc2)
Router uptime is 1 minute System returned to ROM by reload System image file is "flash:c3620-i-mz.123-16a.bin"
cisco 3620 (R4700) processor (revision 0x81) with 45056K/4096K bytes of memory. Processor board ID 24364364 R4700 CPU at 80MHz, Implementation 33, Rev 1.0 Bridging software. X.25 software, Version 3.0.0. Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
2 FastEthernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
1 ISDN Basic Rate interface(s) DRAM configuration is 32 bits wide with parity disabled.
29K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x0
Router#sh boot ^ % Invalid input detected at '^' marker.
Router#sh bootvar ^ % Invalid input detected at '^' marker.
Router#show bootvar ^ % Invalid input detected at '^' marker.
situation boot-start-marker boot system flash flash:c3620-i-mz.123-16a.bin boot-end-marker
Boot OK!
situation boot-start-marker boot-end-marker
Boot OK!
situation boot-start-marker boot system tftp c3620-ik9o3s-mz.122-37.bin 10.0.0.195 boot-end-marker
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) C3600 processor with 49152 Kbytes of main memory Main memory is configured to 32 bit mode with parity disabled
program load complete, entry point: 0x80008000, size: 0x75f414 Self decompressing the image : ################################################# #################################### [OK]
Smart Init is disabled. IOMEM set to: 10
Using iomem percentage: 10
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) C3600 processor with 49152 Kbytes of main memory Main memory is configured to 32 bit mode with parity disabled
rommon 1 >
Router#sh run Building configuration...
Current configuration : 761 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! ! memory-size iomem 10 no aaa new-model ip subnet-zero ! ! ip cef ! ! ! ! ! interface FastEthernet0/0 ip address 10.0.0.82 255.255.255.0 duplex auto speed auto ! interface Serial0/0 no ip address shutdown clock rate 2000000 no fair-queue ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/1 no ip address shutdown clock rate 2000000 ! interface BRI1/0 no ip address shutdown ! interface Ethernet1/0 no ip address shutdown half-duplex ! ip http server ip classless ! ! ! line con 0 line aux 0 line vty 0 4 login ! ! end
1=2E retry one of the test that ends up in ROMMON mode and capture the output of the ROMMON set command
ROMMON 1>
set
post output
from ROMMON mode can you boot the taget image from the tftp server using the boot command ?
boot
you may have to set boot variables ( see below)
again a session log should be posted with outcome
++++++++++++++++++++++++++++++++++++++++++++
If the tftpdnld ROMmon command recovery procedure fails, verify that the following conditions are met:
The TFTP server is running.
The Cisco IOS=AE file is in the root directory of the TFTP server.
The filesize of the Cisco IOS image being uploaded is correct.
If using Cisco TFTP Server 1.1, deselect the two check boxes in View > Options for logging and file transfer progress.
If possible, connect directly to the PC running the TFTP server with a crossover cable.
The file being uploaded is compatible with hardware and memory requirements.
If the router has two built-in Ethernet or fast Ethernet interfaces, always use the first interface (usually 0/0). You must use the built-in interface. For example, if a Cisco 1700 series router has a WIC-1ENET card installed, the tftpdnld ROMmon command does not work with that card.
All variable commands must be upper case. The variable itself is case sensitive as in the case of a filename, as shown in the following example:
rommon11>TFTP_FILE=3Dc2600-i-mz.120-7.T.bin
TFTP_FILE=3D must be upper case and c2600-i-mz.120-7.T.bin is case sensitive.
The DEFAULT_GATEWAY=3D address should not be the same address as the IP_ADDRESS=3D variable. This causes the process to fail. Set the DEFAULT_GATEWAY=3D variable to the address of the TFTP server.
The following example shows how to perform a tftpdnld ROMmon command recovery procedure with a TFTP server at the 10.1.1.2 address, a
255.255.255.0 subnet mask, and a filename of c2600-is-mz.120-7.T.bin.:
rommon 16 > IP_ADDRESS=3D10.1.1.1 !--- This is the temporary IP address assigned to the router. rommon 17 > IP_SUBNET_MASK=3D255.255.255.0 !--- Same as on the TFTP server. rommon 18 > DEFAULT_GATEWAY=3D10.1.1.2 !--- Use the IP address of the TFTP server. rommon 19 > TFTP_SERVER=3D10.1.1.2 !--- TFTP server's IP address. rommon 20 > TFTP_FILE=3Dc2600-is-mz.120-7.T.bin
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) C3600 processor with 49152 Kbytes of main memory Main memory is configured to 32 bit mode with parity disabled
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) C3600 processor with 49152 Kbytes of main memory Main memory is configured to 32 bit mode with parity disabled
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) C3600 processor with 49152 Kbytes of main memory Main memory is configured to 32 bit mode with parity disabled
System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) C3600 processor with 49152 Kbytes of main memory Main memory is configured to 32 bit mode with parity disabled
rommon 1 >
I don`t no what to do next! How to solve this problem?
Cabling-Design.com Forums website is not affiliated with any of the manufacturers or service providers discussed here.
All logos and trade names are the property of their respective owners.