Cisco Systems

  1. Home
  2. Cisco Systems
14705 Threads Posts
to

Worth reading in Cisco Systems

Upgrade PIX515E to PIX 7.0(1) = Flash I/O Error

Hello, I am trying to upgrade a Cisco PIX 515E from 6.3(4) to version 7.0(1). After installing version 7.0(1) binary I...
2 comments posted 21yrs
posted by mark
2 comments posted 21yrs posted by mark

tracert router missing ?

A little testbed lan at home with a 1600 and a 2500 ; I see that when I do a dos tracert from a PC who's gateway points...
1 comments posted 21yrs
posted by arthur
1 comments posted 21yrs posted by arthur

Voip and load-sharing per-packet

I have two routers 1760 which connect together via two T1s with load-sharing per-packet option. The documentation says...
1 comments posted 21yrs
posted by dt1649651
1 comments posted 21yrs posted by dt1649651

Heres a good one.. IPSec VPN question

Hi All, Does anyone know if an IPSec VPN (between two PIX 501 over a T1) can stay established if there is a continuous 4...
10 comments posted 21yrs
posted by rgraves_22*NONONONO*
10 comments posted 21yrs posted by rgraves_22*NONONONO*

Cisco VPN3030 Lan to lan NAT

Setup: ClientA -- NetA -- VPN3030 ....@.... FW-1NG -- NetB -- Server Desc: ClientA on NetA (10.0.0.0/8) needs access Ne...
0 comments posted 21yrs
posted by bilgravCUTTHISOUT
0 comments posted 21yrs posted by bilgravCUTTHISOUT

PIX - ip local pool - question

Hi, -I have a PIX 506 6.3(3) configured with a vpngroup. -The vpngroup is calling an ip local pool ip local pool vpnpoo...
1 comments posted 21yrs
posted by mcaissie
1 comments posted 21yrs posted by mcaissie

ISO flow-based policy editor for PIX

I am searching for a flow-based policy editor / configuration generator suitable for use with PIX. For example, I would...
2 comments posted 21yrs
posted by roberson
2 comments posted 21yrs posted by roberson

GRE tunnel through firewall

Hello all, I am trying to setup a GRE tunnel between 2 routers, one of which is located behind an Astaro firewall. I ha...
1 comments posted 21yrs
posted by 123
1 comments posted 21yrs posted by 123

T1 troubleshooting #2

I have two sites with Two T1's between them. I one end I place the loopback plug and I see the proper: Serial..up, Line...
1 comments posted 21yrs
posted by r
1 comments posted 21yrs posted by r

Problems with DSL not backing up a failed T1

Hi All, I was wondering if anyone has an example configuration for setting up a router to switch over to DSL in the cas...
2 comments posted 21yrs
posted by cosmicspin
2 comments posted 21yrs posted by cosmicspin

help with C831 to C831 vpn

Hi. I've been beating my head against the wall for weeks now trying to get even a simple tunnel between these two to wo...
6 comments posted 21yrs
posted by bluebeeryale
6 comments posted 21yrs posted by bluebeeryale

Router does not respond in console

I just got three used 2501 Cisco routers and am trying to connect to through the console. I had a RJ-45/DB9 cable hooke...
3 comments posted 21yrs
posted by Thread7
3 comments posted 21yrs posted by Thread7

Pix as ipsec endpoint only?

Hello, Because of the way our Quest PRN network is setup and the fact that there is already a firewall in place on Ques...
4 comments posted 21yrs
posted by marv
4 comments posted 21yrs posted by marv

QOS and bandwidth for ADSL

Hello. I'm attempting to provide some priority (not exactly QOS) on a Cisco 827 for VOIP. The trouble I'm having is por...
0 comments posted 21yrs
posted by dwilson
0 comments posted 21yrs posted by dwilson