Cisco Systems

  1. Home
  2. Cisco Systems
14705 Threads Posts
to

Worth reading in Cisco Systems

Catalyst 3750 ISO update?

Hi all, We are stating to use the new Catalyst 3750 switches in stacks of nine. We have noticed problems with ISO versi...
2 comments posted 21yrs
posted by thefunnel
2 comments posted 21yrs posted by thefunnel

server load balancing using a cisco

Hello, i need some advice selecting cisco hardware for the place i work at. we need to load balance some high traffic h...
6 comments posted 21yrs
posted by mazzawi
6 comments posted 21yrs posted by mazzawi

Getting used/free channel of E1 on AS5400

Hi all, do any of you use SNMP to get number of free/used channels in E1 on AS5400? Which variable do you pool to do th...
0 comments posted 21yrs
posted by vina.bfgerf
0 comments posted 21yrs posted by vina.bfgerf

Activating telnet on dialer interface

Hi, I'm a bit of a Cisco newb, so some help would be appreciated. I have a Cisco 827h that is acting as a basic DSL mod...
3 comments posted 21yrs
posted by youngerpants
3 comments posted 21yrs posted by youngerpants

Oversize packets

We have an issue between a Catalyst Switch and a 3Com Switch. Everithing seem fine, the users and network speed are ok,...
2 comments posted 21yrs
posted by aservin
2 comments posted 21yrs posted by aservin

PBR

I am attempting to use policy based routing for the purpose of configuring load balancing between T1 frame relay on C28...
0 comments posted 21yrs
posted by stormrunner'_removethis'
0 comments posted 21yrs posted by stormrunner'_removethis'

Cisco 2950 doesn't recognise VTP commands

I have a 2950 switch on version 12.0(5.3)WC(1).I am trying to change VTP mode to transparent. According to the Cisco do...
4 comments posted 21yrs
posted by alexz
4 comments posted 21yrs posted by alexz

PRI to BRI multilink failure.

Far end is a 3Com ISDN U lanmodem. It is configured for dialin and multilink. Near end is a C2610 with a 2ct1 network m...
2 comments posted 21yrs
posted by jsp
2 comments posted 21yrs posted by jsp

fixup protocol for http

I'm doing some work on a PIX 515, attempting to set it up for our network. I've gotten it to pass basic http packets ac...
4 comments posted 21yrs
posted by "B Squared"
4 comments posted 21yrs posted by "B Squared"

Cisco Wireless-G WAG54G configuration problem

Okay, I'll admit it - I've never configured a gateway in my life. Still, first time for everything. After much messing...
2 comments posted 21yrs
posted by max-man
2 comments posted 21yrs posted by max-man

What about TinyROM and standby mode?

Hi all, I found out this sentence "Turn the router to standby" on the following page...
0 comments posted 21yrs
posted by am
0 comments posted 21yrs posted by am

router heaps.

Hi all, sometimes my router is busy at 25-30% and the most time-consuming process is Check heaps. Does anyone know what...
1 comments posted 21yrs
posted by am
1 comments posted 21yrs posted by am

walter , did I do this right ?

access-list outside_access_in permit tcp any interface outside range 3060 3064 static (inside,outside) udp interface 30...
1 comments posted 21yrs
posted by support
1 comments posted 21yrs posted by support

IOS IDS config ?

I know you can exclude specific signatures with the ip audit signature disable command but is there a way to just speci...
0 comments posted 21yrs
posted by _bill_
0 comments posted 21yrs posted by _bill_