Cisco Systems

  1. Home
  2. Cisco Systems
14705 Threads Posts
to

Worth reading in Cisco Systems

Cisco 1700 router port forwarding

Does someone know how can i open 1 TCP port from my router to 1 computer that is connected to it?
2 comments posted 21yrs
posted by sinisa_n
2 comments posted 21yrs posted by sinisa_n

HDLC invalid serial type code message

I'm trying to connect a WIC-1T on 3660 (IOS 12.1) to a WIC-1T on a 2811 (IOS 12.3) via a fraction of a T-1. Our interal...
1 comments posted 21yrs
posted by randy.smith
1 comments posted 21yrs posted by randy.smith

Help With Intial Vlan

Greetings, I am setting up a vlan, my first, but needed some help. I have an odd setup, and need some help. For the dis...
0 comments posted 21yrs
posted by troute_kilgore
0 comments posted 21yrs posted by troute_kilgore

still befuddled by port forwarding

( cisco 831 router. Using Verizon DSL - I dont have a static IP. ) I have always been able to make progress and eventua...
9 comments posted 21yrs
posted by StephenRichter
9 comments posted 21yrs posted by StephenRichter

Query regarding frame relay CIR

Hi, I have a frame relay link driven by a Cisco 2620 router. I am paying the carrier company for a CIR of 1.5 Mbps. Mos...
5 comments posted 21yrs
posted by satishj
5 comments posted 21yrs posted by satishj

BGP vs OSPF routes validity

I have got a problem with BGP routes. Got 2 Gateways. They are connected to BGP and to OSPF and they do mutual redistri...
3 comments posted 21yrs
posted by matteo_cardelli
3 comments posted 21yrs posted by matteo_cardelli

Newbie Catalyst question

Hi - apologies for what is probably a dumb question. I need to temporarily disable one of the ethernet ports on a Catal...
3 comments posted 21yrs
posted by cisco_newbie
3 comments posted 21yrs posted by cisco_newbie

The round-trip delay in communicating with the host

Hi, I'm using the extended ping command for troubleshooting the accessibility of remote devices. when i ping this parti...
0 comments posted 21yrs
posted by riyadhb2000
0 comments posted 21yrs posted by riyadhb2000

The Ping Coomand

Hi, I'm a new CCNA holder and still a fresh starter. I whould like to the definitions of the following line after issui...
4 comments posted 21yrs
posted by riyadhb2000
4 comments posted 21yrs posted by riyadhb2000

changing both source and destination with nat

How can I change both the source and destination addresses of incoming packets? Assuming the following configuration: i...
1 comments posted 21yrs
posted by cwarden
1 comments posted 21yrs posted by cwarden

Monitor interface is down

Have monitoring going on a destination port on a C2950: monitor session 1 source interface Gi0/2 monitor session 1 dest...
1 comments posted 21yrs
posted by cptnzod
1 comments posted 21yrs posted by cptnzod

Boot problem on Cisco 1600 serie

Hello all , I have a 1600 serie router which don't start properly. After few seconds I have a the following prompt : Na...
2 comments posted 21yrs
posted by titi
2 comments posted 21yrs posted by titi

service port commands reference

using the Cisco 831 router ... Looking for a good router service port commands reference guide. Web site, Cisco manual,...
3 comments posted 21yrs
posted by StephenRichter
3 comments posted 21yrs posted by StephenRichter

problems forwarding http to PC

using the cisco 831 on a verizon dsl connect to the internet ... just experimenting, I dont have a static IP address, I...
2 comments posted 21yrs
posted by StephenRichter
2 comments posted 21yrs posted by StephenRichter