Cisco Systems

  1. Home
  2. Cisco Systems
14704 Threads Posts
to

Worth reading in Cisco Systems

Pointer in the correct direction...

Hi, would someone please give me a pointer in the correct direction? I would like to think that I'm a fairly experience...
1 comments posted 20yrs
posted by gtaylor
1 comments posted 20yrs posted by gtaylor

Load-balancing across four T1's on 2 routers

I am setting up the following: - 2 Cisco 2800 series routers, each has two T-1 internet connections. - Those 2 routers...
35 comments posted 20yrs
posted by sean-usenet
35 comments posted 20yrs posted by sean-usenet

Cisco Access points

Hi everyone, Could anyone help me. I currently own a warehouse of 10,000sq/ft with a height of 6ft. It is completely ra...
2 comments posted 20yrs
posted by number1hatfielder
2 comments posted 20yrs posted by number1hatfielder

ACLS not showing up in PDM or working properly

Hi, I have some basic ACL's that i'm adding to the PIX 501 as follows: object-group network WWWAccessOnly3 network-obje...
1 comments posted 20yrs
posted by anonymous
1 comments posted 20yrs posted by anonymous

Access points on wheels

I have two Aironet 1240 APs. One of them is installed in a vehicle, which also contains several wireless clients. The o...
6 comments posted 20yrs
posted by pm
6 comments posted 20yrs posted by pm

Port Forwarding / VPN Pass-Thru on a Cisco 2800

I have a Cisco 2800 that is being used as a firewall. When I am behind it and NATing to the Internet I am unable to VPN...
1 comments posted 20yrs
posted by piperace
1 comments posted 20yrs posted by piperace

CDP Application

(Cross posted into alt.certification.cisco) Guys Recently my very old and aged copy of Cisco Works V3 running on Window...
4 comments posted 20yrs
posted by nochance
4 comments posted 20yrs posted by nochance

PIX 501 unable to map port. Plx help

Need to map ports through on a PIX 501, and have the following static rules setup: static (outside,inside) tcp 192.168....
6 comments posted 20yrs
posted by noway
6 comments posted 20yrs posted by noway

Aironet Client Utility 802.1X+PEAP.

Hi Guys, I've installed the release 6.6. I need to use 802.1X with a certificate (generated by ACS) plus PEAP. But the...
1 comments posted 20yrs
posted by am
1 comments posted 20yrs posted by am

upgrade from 6.3(5) to 7.12?

Hi, We are currently using Cisco PIX version 6.3(5), with 128mb memory. I'm trying to figure out if it is usefull to up...
1 comments posted 20yrs
posted by ferocius_net
1 comments posted 20yrs posted by ferocius_net

PIX capture pppoe traffic

Hi, Im having some trouble capturing traffic going out from my pix through the outside interface. I've turned on "captu...
2 comments posted 20yrs
posted by anders.lastad
2 comments posted 20yrs posted by anders.lastad

Cisco 5002 card question

Hi I have a Cisco Catalyst 5002 switch that I purchased very cheaply to play about with. It has a supervisor module and...
2 comments posted 20yrs
posted by dilan.weerasinghe
2 comments posted 20yrs posted by dilan.weerasinghe

The 1900 and 2900 switches

Any body please can lead me to a place where I can see a comparison between the commands for configuring the two types o...
2 comments posted 20yrs
posted by lrantisi
2 comments posted 20yrs posted by lrantisi

Low latency queueing over Tunnel interfaces

Hi Can anyone tell me if you can do low latency queueing over tunnel interfaces? We wish to setup some QOS for a client...
2 comments posted 20yrs
posted by scooty
2 comments posted 20yrs posted by scooty