Cisco Systems

  1. Home
  2. Cisco Systems
14701 Threads Posts
to

Worth reading in Cisco Systems

Routing with multiple Interfaces

I have a Cisco 2811 that has 2 Fast Ethernet interfaces. One interface I want to use to control "Routes" on my local pr...
4 comments posted 19yrs
posted by mdfields13
4 comments posted 19yrs posted by mdfields13

Port blocked - Cisco router or PIX

We have an application that works requires, say inbound port 103 (example). It is not working, and the programmers thin...
2 comments posted 19yrs
posted by kammy_boy186
2 comments posted 19yrs posted by kammy_boy186

Can't read or format ata flash card on 6500

Been trying to sort this one, had a scan of similar threads. I have a 6509 running hybrid, can't read the flash from th...
2 comments posted 19yrs
posted by specialist_net
2 comments posted 19yrs posted by specialist_net

Interconnecting two pbx over CEoIP

Hi, I have two PBX and CEoIP between them. PBX2 cannot get a clock from the PBX1. Configuration: PBX1 -E1- R1 -IP- R2 -...
1 comments posted 19yrs
posted by vlaho.izbrisiovajdijojemin
1 comments posted 19yrs posted by vlaho.izbrisiovajdijojemin

alias command issue in ASA 7.22 on a pix

alias (inside) command that was working fine in 6.3 is hosing connectivity to the inside address after upgrade to 7.22....
0 comments posted 19yrs
posted by _ns
0 comments posted 19yrs posted by _ns

bridge + cisco 877 + ADSL

Hello, I'm trying to mahke a cisco 877 (ios 14.4) router on bridge mode between ATM0 and Fastehernet0 (for PPPOE). It s...
2 comments posted 19yrs
posted by mickael.kael
2 comments posted 19yrs posted by mickael.kael

CCM or CCME ?

Hello, I'm new with Cisco. We are completly rebuilding our sites and we look to use VOIP. We have 3 sites : - 1 in Belg...
4 comments posted 19yrs
posted by AEnlevergeoffrey
4 comments posted 19yrs posted by AEnlevergeoffrey

PIX site to site VPN, ACL = deny; no sa created

Problem at HeadOffice: IPSEC(sa_initiate): ACL = deny; no sa created. I've read that this is caused by Proxy mismatches...
1 comments posted 19yrs
posted by nicough
1 comments posted 19yrs posted by nicough

Setting up outside SSH on a DHCP interface

I am working on setting up an external SSH connect to my pix501 however I was told that because my outside interface is...
2 comments posted 19yrs
posted by tehlotus
2 comments posted 19yrs posted by tehlotus

Copy PIX Config

I am running a pix 515e and I want to copy the configs to a tftp server that is running on my workstation at 192.168.10...
2 comments posted 19yrs
posted by paul
2 comments posted 19yrs posted by paul

VoIP + 3650 PoE = Echo + Dropped Calls...etc

Troubleshooting a setup involving three 3650 48 port 10/100 PoE switches with GBit uplinks to each other. PC linked off...
2 comments posted 19yrs
posted by amattina
2 comments posted 19yrs posted by amattina

HTTP Server privilege seperation

Does anyone know what needs to be added to a privilege level to allow use of the web administration page for the port co...
4 comments posted 19yrs
posted by jerkart
4 comments posted 19yrs posted by jerkart

Config lost after switch turned off

Hello, I have a Cisco Switch Catalyst 3548XL. Everytime the switch has been turned off i lose my configuration and it g...
2 comments posted 19yrs
posted by hello_2you
2 comments posted 19yrs posted by hello_2you

Replacing ISP managed router in office

Hi, We are running the following topology - 'Demarc' - CSU/DSU - Cisco 2501 Router - Cisco PIX Firewall - 3 x Cisco 295...
4 comments posted 19yrs
posted by smokejo
4 comments posted 19yrs posted by smokejo