cisco 827 sbc, AT&T setup

You may wish to investigate the Cisco 827 Config Wizard:

Cisco 827 Basic Configuration:

Cisco 827 Firewall Configuration:

Cisco 827 Firewall PPTP Configuration:

Cisco 827 Business Configuration:

Cisco 827 ADSL IPSec Configuration:

Cisco 827 Firewall IPSec configuration:

Cisco 827 GUI Config:

Hope this helps.

Brad Reese Cisco Technical Forums

! The dialer is associated with the ADSL interface atm0 which is in shutdown mode ...

config t

! for future troubleshooting

no service pad service timestamps debug datetime localtime service timestamps log datetime localtime logging buffered 10000 debugging no logging console

! take ADSL interface out of shutdown mode

interface ATM0 no bundle-enable no shutdown

interface ATM0.1 point-to-point pvc 0/100 encapsulation aal5mux ppp dialer dialer pool-member 1

! fix up Ethernet interface config

interface Ethernet0 no pppoe enable no pppoe-client dial-pool-number 1 no hold-queue 100 out ! do not use hold queues unless having packet drops

! configure 827 as DHCP server if devices on inside LAN need to be assigned IP addresses

ip dhcp excluded-address 10.10.10.1

ip dhcp pool DHCP_POOL_1 import all network 10.10.10.0 255.255.255.0 default-router 10.10.10.1

end

wri mem

thanks to all that tried to help me, now the interfaces are all up, but I cannot ping anything outside of my router, internal LAN is fine, ========================================= ateway of last resort is 0.0.0.0 to network 0.0.0.0

C 192.168.1.0/24 is directly connected, Ethernet0 S* 0.0.0.0/0 is directly connected, Dialer0 ========================================= is there anyone around who had configured 827 with SBC dsl? I think it is one of the parameters such as the encapsulation type...

here is my config: =============================================================== Current configuration : 1494 bytes ! version 12.3 no service pad service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname 827 ! boot-start-marker boot-end-marker ! ! no aaa new-model ip subnet-zero ip name-server 68.94.156.1 ip name-server 68.94.157.1 ip dhcp excluded-address 192.168.1.1 192.168.1.100 ip dhcp excluded-address 192.168.1.254 ! ip dhcp pool dhcppool import all network 192.168.1.0 255.255.255.0 default-router 192.168.1.254 dns-server 68.94.157.1 ! ! ! ! ! ! ! interface Ethernet0 ip address 192.168.1.254 255.255.255.0 ip nat inside hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode auto ! interface ATM0.1 point-to-point pvc 0/100 encapsulation aal5snap protocol ppp dialer dialer pool-member 1 ! ! interface Dialer0 bandwidth 640 ip address negotiated no ip redirects no ip unreachables ip nat outside encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp pap sent-username uname password 7 mypass ppp ipcp dns request ! ip nat inside source list 1 interface Dialer0 overload ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 no ip http server no ip http secure-server ! access-list 1 permit 192.168.1.0 0.0.0.255 dialer-list 1 protocol ip permit ! ! line con 0 transport preferred all transport output all stopbits 1 line vty 0 4 login transport preferred all transport input all transport output all ! scheduler max-task-time 5000 end

post a show int dialer0, are you getting an IP?

it doesn't look like I am getting an ip, the user name and password are correct, just checked. =============================================================

827#sh ip int brief Interface IP-Address OK? Method Status Protocol ATM0 unassigned YES NVRAM up up ATM0.1 unassigned YES unset up up Dialer0 unassigned YES NVRAM up up Ethernet0 192.168.1.254 YES NVRAM up up Virtual-Access1 unassigned YES unset up up Virtual-Access2 unassigned YES unset up down 827#show int dialer0 Dialer0 is up, line protocol is up (spoofing) Hardware is Unknown Internet address will be negotiated using IPCP MTU 1500 bytes, BW 640 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, loopback not set Keepalive set (10 sec) DTR is pulsed for 1 seconds on reset Interface is bound to Vi2 Last input never, output never, output hang never Last clearing of "show interface" counters 00:43:29 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/0/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 480 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes 0 packets output, 0 bytes Bound to: Virtual-Access2 is up, line protocol is down Hardware is Virtual Access interface MTU 1500 bytes, BW 640 Kbit, DLY 100000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, LCP Closed PPPoATM vaccess, cloned from Dialer0 Vaccess status 0x44 Bound to ATM0.1 VCD: 1, VPI: 0, VCI: 100, loopback not set Interface is bound to Di0 (Encapsulation PPP) Last input never, output never, output hang never Last clearing of "show interface" counters 00:33:34 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions