Hi, all!
I have some trouble with Catalyst 4003 and WS-X4306 module. After power on come on diag modules (first, second and the third at last). All GBIC slots has "OK" in this test (include module 3 - WS-X4306), page down to look the log. But after start system module has red leds and "module 3 is not installed" in system. For example for reset module:
--------------------- cisco> (enable) reset 3 Module 3 is not installed.
---------------------
CatOS version 6.1.1, try to upgrade on new CatOS 7.4.3 nothing results
Start log:
---------------------------------------------------------------------------- WS-X4012 bootrom version 5.4(1), built on 2000.04.04 10:48:54 H/W Revisions:????Meteor:?4????Comet:?8????Board:?2 Supervisor MAC addresses: 00:04:4e:fd:14:00 through 00:04:4e:fd:17:ff (1024 addresses) Installed memory: 64 MB Testing LEDs.... done! The system will autoboot in 5 seconds. Type control-C to prevent autobooting. rommon 1 >
The system will now begin autobooting. Autobooting image: "bootflash:cat4000.6-1-1.bin" .....................................................................................................................############################## Starting Off-line Diagnostics Mapping in TempFs Board type is WS-X4012 DiagBootMode value is "post" Telling ApkPageMan that we have 12288 pages of memory Loading diagnostics...
Power-on-self-test for Module 1:??WS-X4012 Status: (. = Pass, F = Fail) processor: .???????????cpu?sdram:?.???????????rtc:?. eprom: .???????????????nvram:?.???????????????flash:?. temperature sensor: .??enet?console?port:?.???switch?port?0:?. switch port 1: .???????switch?port?2:?.???????switch?port?3:?. switch port 4: .???????switch?port?5:?.???????switch?port?6:?. switch port 7: .???????switch?port?8:?.???????switch?port?9:?. switch port 10: .??????switch?port?11:?.??????switch?registers:?. switch sram: . Module 1 Passed
Power-on-self-test for Module 2:??WS-X4232-GB-RJ Port status: (. = Pass, F = Fail) ?1:?.???2:?.???3:?.???4:?.???5:?.???6:?.???7:?.???8:?. ?9:?.??10:?.??11:?.??12:?.??13:?.??14:?.??15:?.??16:?.
17: .??18:?.??19:?.??20:?.??21:?.??22:?.??23:?.??24:?. 25: .??26:?.??27:?.??28:?.??29:?.??30:?.??31:?.??32:?. 33: .??34:?. Module 2 PassedPower-on-self-test for Module 3:??WS-X4306-GB Port status: (. = Pass, F = Fail) ?1:?.???2:?.???3:?.???4:?.???5:?.???6:?. Module 3 Passed
Exiting Off-line Diagnostics
Cisco Systems, Inc. Console
----------------------------------------------------------------------------
cisco> (enable) sho ver WS-C4003 Software, Version NmpSW: 6.1(1) Copyright (c) 1995-2000 by Cisco Systems, Inc. NMP S/W compiled on Sep 30 2000, 12:25:52 GSP S/W compiled on Sep 28 2000, 18:28:28
System Bootstrap Version: 5.4(1)
Hardware Version: 2.1 Model: WS-C4003 Serial #: JAE050201X4
Mod Port Model Serial # Versions
--- ---- ---------- -------------------- ---------------------------------
1 0 WS-X4012 JAE050201X4 Hw : 2.1 Gsp: 6.1(1.0) Nmp: 6.1(1) 2 34 WS-X4232-GB-RJ JAE0441043H Hw : 2.3DRAM FLASH NVRAM Module Total Used Free Total Used Free Total Used Free
------ ------- ------- ------- ------- ------- ------- ----- ----- -----
1 65536K 27831K 37705K 12288K 9139K 3149K 480K 168K 312K