5500 module

U

ufik 18 years ago

Hello,

What is mean faulty status. It is hardware problem or something else. Is it normal status for Supervisor?

5500> (enable) sh module Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- ---

--------

1 1 2 1000BaseSX Supervisor WS-X5530 yes faulty
2 2 Gigabit Ethernet Ext WS-X5410
3 3 9 Gigabit Ethernet WS-X5410 no ok
6 6 12 100BaseFX MM Ethernet WS-X5201 no ok
7 7 1 Route Switch WS-X5302 no ok
8 8 12 10BaseFL Ethernet WS-X5011 no ok
9 9 12 100BaseFX MM Ethernet WS-X5111 no ok
10 10 24 10/100BaseTX Ethernet WS-X5224 no ok
11 11 36 10/100BaseTX Ethernet WS-X5239 no ok
12 12 36 10/100BaseTX Ethernet WS-X5239 no ok

Thank you for help.

Vote

M

make 18 years ago

What about "show test 1" ? "show test diaglevel" ? "show system" ?

Vote

U

ufik 18 years ago

On 6 Sie, 19:45, make wrote:

500> (enable) show test 1

Diagnostic mode: minimal (mode at next reset: minimal)

Module 1 : 2-port 1000BaseSX Supervisor Network Management Processor (NMP) Status: (. = Pass, F = Fail, U = Unknown) ROM: . Flash-EEPROM: . Ser-EEPROM: . NVRAM: . MCP Comm: .

EARL III Status : DisableIndexLearnTest: . DontLearnTest: . DisableNewLearnTest: . ConditionalLearnTest: . MonitorColorFloodTest: . EarlTrapTest: . StaticMacAndTypeTest: . BadDvlanTest: . BadBpduTest: . IndexMatchTest: . ProtocolTypeTest: . IgmpTest: . SourceMissTest: . SourceModifiedTest: . ArpaToArpaShortcutTest: . ArpaToSnapShortcutTest: . SnapToArpaShortcutTest: . SnapToSnapShortcutTest: . SoftwareShortcutTest: . MulticastExpansionTest: . DontShortcutTest: . ShortcutTableFullTest: . ArpaToArpaShortcutTest(IPX): . ArpaToSnapShortcutTest(IPX): . ArpaToSapShortcutTest(IPX): . ArpaToRawShortcutTest(IPX): . SnapToArpaShortcutTest(IPX): . SnapToSnapShortcutTest(IPX): . SnapToSapShortcutTest(IPX): . SapToArpaShortcutTest(IPX): . SapToSnapShortcutTest(IPX): . SapToSapShortcutTest(IPX): . SapToRawShortcutTest(IPX): . RawToArpaShortcutTest(IPX): . RawToSnapShortcutTest(IPX): . RawToSapShortcutTest(IPX): . RawToRawShortcutTest(IPX): . SoftwareShortcutTest(IPX): . DontShortcutTest(IPX): . ShortcutTableFullTest(IPX): .

Line Card Diag Status for Module 1 (. = Pass, F = Fail, N = N/A) CPU : . Sprom : . Bootcsum : . Archsum : . RAM : . LTL : . CBL : . DPRAM : . SAMBA : . Saints : N Pkt Bufs : . Repeater : N FLASH : . Phoenix : . TrafficMeter: . UplinkSprom : . PhoenixSprom: .

PHOENIX Status : Ports T1 R1 T2 R2 --------------------- . . . .

GIGMAC Status : Ports 1 2 ----------- . .

PHOENIX Port Status : Ports 9 17 18 19 20 21 22 INBAND A->B B->A B->C C->B A->C C->A ------------------------------------------ . . . . . . .

Packet Buffer Status : Ports 1 2 ----------- . .

PHOENIX Packet Buffer Status : Ports INBAND AB BC AC ------------------------------ . . . .

Loopback Status [Reported by Module 1] : Ports 1 2 9 -------------- . . .

5500> (enable) show system PS1-Status PS2-Status

---------- ---------- ok faulty

Fan-Status Temp-Alarm Sys-Status Uptime d,h:m:s Logout

---------- ---------- ---------- -------------- --------- ok off faulty 0,04:51:43 20 min

PS1-Type PS2-Type

------------ ------------ WS-C5508 WS-C5508

Modem Baud Traffic Peak Peak-Time

------- ----- ------- ---- ------------------------- disable 9600 0% 2% Mon Aug 6 2007, 19:23:22

5500> (enable) show test diaglevel Diagnostic mode at last bootup : minimal Diagnostic mode at next reset : minimal

Vote

S

Scott Perry 18 years ago

A Cisco Catalyst 5500 series switch will report module 1, the supervisor, as faulty when one of the two power supplies is not working.

Turn the other power supply on or else replace the power supply unit if it has failed.

Vote

M

make 18 years ago

Its power supply 2. > 5500> (enable) show system > PS1-Status PS2-Status > ---------- ---------- > ok faulty

Vote

U

ufik 18 years ago

Yes, now its ok thank you

Vote

5500 module

Join the Discussion

Didn't find your answer?