Latest threads in Cisco Systemsshow only best voted threads
| Subject | Author | Posted | Replies | |
|---|---|---|---|---|
|
|
VoIP and Packet Size
I've been asked to prioritize VoIP traffic for a customer that uses a private wireless network managed by another contractor for transport from the remote sites to headquarters. All VoIP traffic...
1
|
17 years ago
|
1 | |
|
|
Config Help-I'm being Lazy
Can any of you Cisco guru's create a sample config file for the following setup. I'm attempting to let the experts do this so It's gets done right (and I don't have to read the manual to figure out...
10
|
17 years ago
|
10 | |
|
|
MIB for Cat 4500 module standby status
This is a really easy one :-)) I want to use snmp to detect the standby status of the supervisors in a Catalyst 4500 (SE IV) with recent IOS. 1.3.6.1.4.1.9.3.6.11.1.9 cardOperStatus -- looks ideal...
—
|
17 years ago
|
— | |
|
|
Access Point and CS ACS and AD configuration
I have got 15 wireless AP Aironet 1100, and I want to use Cisco Secure ACS V3. 3 and we have got windows Active Directory 2003 as well. I am looking to for document that shows me how to configure...
—
|
17 years ago
|
— | |
|
|
cisco 1700
i have this router that was configured and working fine until recently. it is showing this error i have never seen be4...loadprog: bad file magic number: 0x0 boot: cannot load "flash:" Pliz help.
1
|
17 years ago
|
1 | |
|
|
ASA 5510 UDP NAT problem
Hello all, Just received new ASA 5510 and am doing initial testing and config in my lab. I have set up three interfaces e0/0 as inside security=100 e0/1 as dmz security=50 e0/2 as outside security=0 I...
8
|
17 years ago
|
8 | |
|
|
Cisco Pix 515 Question - Hyperterminal cut/paste
How does one completely replace the code on a Pix 515? I saw someone do this using Hyperterminal with Cut/Paste a few years ago, but cannot reproduce. Thanks, G
1
|
17 years ago
|
1 | |
|
|
Errors
Hi All, I connected PIX firewall and internet router using cross cable,iam experiencing input errors and ignored in ethernet interface router. Received 150 broadcasts, 0 runts, 0 giants, 962 throttles...
2
|
17 years ago
|
2 | |
|
|
How is this done..
Hi I would like to take in a PSTN call in the USA and upon accepting the call present the User which a internet link which another application will make the Telnet connection to a open Server...
1
|
17 years ago
|
1 | |
|
|
Redundancy
Hi, Iam having 100Mbps metro ethernet link and 2Mbps serial link terminated in same router.Iam using 100Mb link as primary route and give serial link as second problem is when ethernet link goes down...
1
|
17 years ago
|
1 | |
|
|
Cisco ACS user creation
Hi all. don't know if this is in-topic here, hope yes. I have the need to automatically create users on a Cisco Secure ACS server (ver 3.3 for windows). So I don't want to use the HTML interface, but...
—
|
17 years ago
|
— | |
|
|
ASA - logging via radius with group name passed.
Hi, I'm trying to setup ASA5520 with Radius to authenticate users with group privileges. Useing Radius with ASA to authenticate users is quite simple. When I try to pass from asa tunnel-group name...
—
|
17 years ago
|
— | |
|
|
Forward VLAN traffic to separate MPLS L2 VPN's
Hello all, Based only on the VLAN the traffic is coming from, how can I forward it to different Pseudowires (MPLS L2 VPN's) ? Thanks everyone
—
|
17 years ago
|
— | |
|
|
Cisco VPN client and Linksys VPN compatibility?
I am pretty familiar with the Cisco VPN device (the one that used to be called Altiga), but I have no experience whatsoever with the Linksys VPN boxes. Can I use my Cisco VPN client to connect to a...
3
|
17 years ago
|
3 | |
|
|
Cisco ASA ver 7.2 SNMP anomolies
Hi, I've got three Cisco devices exhibiting the same phenomenon that I can't find a solution for. One device is an ASA 5510 another device is an ASA 5505 and the third is a PIX 515E. The thing in...
—
|
17 years ago
|
— |