Cisco Systems

  1. Home
  2. Cisco Systems
14701 Threads Posts
to

PIX configuration -- 3 way handshake incomplete

I'm trying to configure my outside device to authenticate to my internal TACACS server. The outside device will need to...
2 comments posted 16yrs
posted by brickwalls19
2 comments posted 16yrs posted by brickwalls19

Dyndns ASA & 871

Hi there, I have an ASA Box as my Gateway to the Internet here. It serves the internal Net 192.168.1.0/24. Also I have...
6 comments posted 16yrs
posted by wqhtny
6 comments posted 16yrs posted by wqhtny

Cisco 2821 ISR config with Wifi

Hi there, I just got a Cisco 2821. I am currently using both of the integrated gigabit interfaces for routing (one loca...
3 comments posted 16yrs
posted by jbaker
3 comments posted 16yrs posted by jbaker

Policy map using policy map

I have been given a template configuration for a DSCP based QoS. So the incoming traffic policy map marks the traffic a...
1 comments posted 16yrs
posted by gsinclairnb
1 comments posted 16yrs posted by gsinclairnb

Bridge-Group blocking traffic to LAN.

I had gotten this to work at one point by blindly trying stuff, but we havd a power and I lost those settings and I am...
3 comments posted 17yrs
posted by jfmezei.spamnot
3 comments posted 17yrs posted by jfmezei.spamnot

PIX 501 and DHCPD options

I am having problem with my 501 DHCP server. that PIX box responsible to provide IP addresses for wireless clients via...
4 comments posted 17yrs
posted by rob
4 comments posted 17yrs posted by rob

Cisco 350 Access Point

Hi, Can anyone tell me if the Cisco 350 Access Point will support a dual SSID, with one being WEP encrypted and the oth...
4 comments posted 17yrs
posted by SW
4 comments posted 17yrs posted by SW

atm interface outpktdrops

Dear all, could i get views on the issue of outpktdrops being reported when i do; show int atm0/0 as described below; I...
6 comments posted 17yrs
posted by ipcomp1
6 comments posted 17yrs posted by ipcomp1

Allowing SSH only from trusted subnets

I need to set up some extended ACL's to only allow SSH from trusted subnets. This is what I have come up with so far :...
2 comments posted 17yrs
posted by Lovejoy1
2 comments posted 17yrs posted by Lovejoy1

Which ACL is blocking traffic

Hello, I am trying to figure out wich access list is blocking my attempts to connect to a ASA5500 via Cisco ASDM Launch...
6 comments posted 17yrs
posted by boynton.pete
6 comments posted 17yrs posted by boynton.pete

'no ip classless' not working?

I am playing with some routers in a lab and just to say that I've seen it break things I set 'no ip classless'. However...
7 comments posted 17yrs
posted by tommyj27
7 comments posted 17yrs posted by tommyj27

Trying to monitor port on Cisco 1841

Anybody know what's going on here? I am trying to monitor f0/0 to f0/1, when I go to conf t, I try this: ROUTER(config)...
4 comments posted 17yrs
posted by ponga
4 comments posted 17yrs posted by ponga

wrt110

Installed router and works. Everytime I boot the PC up I get this error message: Linksys Easy Link Advisor-main has enc...
0 comments posted 17yrs
posted by sligo
0 comments posted 17yrs posted by sligo

Site to Site VPN ASA 5505 not creating tunnel

I am somewhat of a newbie at this stuff but I am trying to set up a site to site vpn using two Cisco ASA 5505's. I went...
1 comments posted 17yrs
posted by chunalt787
1 comments posted 17yrs posted by chunalt787