Cisco Systems

  1. Home
  2. Cisco Systems
14701 Threads Posts
to

Copy image from USB to 2821

I am trying to put a new IOS image on a 2821 box, and TFTP after many many tries with different PCs is not working. I h...
6 comments posted 16yrs
posted by roverdrover
6 comments posted 16yrs posted by roverdrover

Cisco SMB (engineer)

Hi, can somebody point me to any documentation related to this certification? (mmmmm, my boss figures we need it ,) and...
5 comments posted 16yrs
posted by geni0us
5 comments posted 16yrs posted by geni0us

how to monitor traffic going through a switch port

Hi everyone, I have been reading pages and pages of information on how to monitor traffic on a cisco router, but it's a...
12 comments posted 16yrs
posted by bernala
12 comments posted 16yrs posted by bernala

Tunneling VPN-Client through ASA

Hello, we have a Cisco ASA 5550 running Software Version 8.2(1)11. We have client computers with non-routed addresses....
0 comments posted 16yrs
posted by gartmann
0 comments posted 16yrs posted by gartmann

2511 access server config or hardware going wrong?

Hi, I recently acquired as part of a job lot a 2511 access server. I purchased the require CAB-OCTAL-ASYNC cables (albe...
5 comments posted 16yrs
posted by jasper.janssen
5 comments posted 16yrs posted by jasper.janssen

AP of the 881 does not see usb flash memory

I have two Cisco 881. I can copy the main config of the one router over the other using the usb flash memory. When I lo...
1 comments posted 16yrs
posted by dt1649651
1 comments posted 16yrs posted by dt1649651

BGP Filtering

Good day Colleagues, I want to ask you advice about the policy for BGP prefix filtering. The main idea is to automatize...
0 comments posted 16yrs
posted by dk77
0 comments posted 16yrs posted by dk77

Router always Starting in ROMMON mode

If power fails then when my router starts always starting in rommon mode. Then when i type rommon1>reset router works fi...
5 comments posted 16yrs
posted by ts.8060
5 comments posted 16yrs posted by ts.8060

General BGP & OSPF Re-Distribution Question

Hi, I set up a simple network in Dynamips. This was a triangle, R1, R2, R3. R1 is connected to R2 (serial) and to R3 (S...
0 comments posted 16yrs
posted by darrenfgreen
0 comments posted 16yrs posted by darrenfgreen

VOIP Recording Help

currently have cablevision as a phone service provider for my private business. I was wondering if anyone has any ideas...
0 comments posted 16yrs
posted by john.j.kaiser
0 comments posted 16yrs posted by john.j.kaiser

Network Performance 1GB ports

Hi, I have a Cisco 2960 with 2 x 1 GB ports. I have plugged a computer on each port. and run a netperf (http://www.osnm...
15 comments posted 16yrs
posted by cpdivers
15 comments posted 16yrs posted by cpdivers

Setting up VPN on 1811 router

I have a Cisco 1811 as my router. Inside there are 2 VLAN's. One VLAN for my desktops and one VLAN as a DMZ for my serv...
0 comments posted 16yrs
posted by googlegroups
0 comments posted 16yrs posted by googlegroups

DNS Record in CISCO Router

I want to configure DNS Record in CISCO Router. I am using Router as internet server with DNS. If i configure it there u...
5 comments posted 16yrs
posted by ts.8060
5 comments posted 16yrs posted by ts.8060

ACL help needed...

This should be simple, but I am doing something wrong. I need a write an PACL that will only allow established traffic...
2 comments posted 16yrs
posted by Lovejoy1
2 comments posted 16yrs posted by Lovejoy1