Cisco Systems

  1. Home
  2. Cisco Systems
14701 Threads Posts
to

Worth reading in Cisco Systems

modem dial-in to Cisco 2600 problem

Password: 2) how can I set that after 3 unsuccessful login attempts, user gets disconnected? 3) Why every time I connec...
1 comments posted 20yrs
posted by asd
1 comments posted 20yrs posted by asd

PIX SSH access

Did anything change in ver 7.2 with SSH access? I get logon prompts but no user accounts can logon... "access denied" o...
5 comments posted 20yrs
posted by nnord
5 comments posted 20yrs posted by nnord

3DES and catalyst.

Which field does the 3DES feature of the Enhanced IOS cover available for the Catalyst SuperVisor? VPN? I don't think so...
0 comments posted 20yrs
posted by am
0 comments posted 20yrs posted by am

Cisco 1900 Password Recovery

I perfomed a Password recovery, many times, at my Cisco 1900, but I hadn=B4t any answer from the switch to PC. I checke...
1 comments posted 20yrs
posted by diogenesmarco
1 comments posted 20yrs posted by diogenesmarco

Cisco connectorrs question

Hi there, I have 2 Courier modems for dialing in, connected to a Cisco 2509 through a DCE RJ45 to 25 pins connectors, l...
1 comments posted 20yrs
posted by CalinGuga
1 comments posted 20yrs posted by CalinGuga

Subnetting Question from ccna - sybex book

For some reason, this question has me lost - particular cidr question Which of the following IP addresses fall into the...
2 comments posted 20yrs
posted by rwest.eagle
2 comments posted 20yrs posted by rwest.eagle

vlan1 problem on cisco 1812

I have setup a cisco 1812 router. I can telnet to the router on vlan1, but when I am logged in I can not ping the vlan1...
6 comments posted 20yrs
posted by oasissw
6 comments posted 20yrs posted by oasissw

Port Speed

Catalyst 2950. If I set a device connecting to the switch to 100/full duplex, is it best to set the switch port to the s...
3 comments posted 20yrs
posted by
3 comments posted 20yrs posted by

allow NTP to synch through a PIX

Hi, I have a client that has a PIX facing the internet. Internally, the client has set up a DMZ and has allowed ssh acc...
1 comments posted 20yrs
posted by tiaanv
1 comments posted 20yrs posted by tiaanv

Help! DMZ on Pix515

I have set up a Pix 515 and internet works fine, but I have a problem with the DMZ. I have a range of addresses, like w...
2 comments posted 20yrs
posted by young_neils
2 comments posted 20yrs posted by young_neils

ISDN Dialup to 2 x Seperate Routers

I have 2 x 2800 Routers, each has a ISDN (BRI) network card installed (WIC-1BS/T). Each BRI has a separate phone number...
2 comments posted 20yrs
posted by darrenfgreen
2 comments posted 20yrs posted by darrenfgreen

Freeware Radius for Windows XP

I have Cisco PIX 501 that I'm using as a firewall and to dial in over VPN. VPN user nhave to be authenticated on Radius...
0 comments posted 20yrs
posted by john.strow
0 comments posted 20yrs posted by john.strow

static ip dsl configuration on a 2811

I have a 2811 on a dsl line that uses nat and an ethernet lan pretty much like any $20 router. I have read these docume...
1 comments posted 20yrs
posted by nick.schmalenberger
1 comments posted 20yrs posted by nick.schmalenberger