WLC 2006

Hi guys, I have a Cisco WLC 2006, with a male DB-9 serial port, i connected a gender changer (Female - Female) to be able to connect the WLC to my laptop using a male DB-9 serial to USB, but i can not connect through the terminal.

I also used a Female to female DB-9 serial cable to connect the WLC to the laptop male DB-9 but also dod not work.

Am i missing something here in the WLC serial pins?

I used the usual terminal settings:

9600 baud

8 data bits

1 stop bit

No parity

No hardware flow control

Reply to
Andy
Loading thread data ...

Thx, sometimes we do not read the manual properly.

Reply to
Andy

Hi guys, i am having a problem with one of the 1200 LWAP to join the controler, i can ping the controler from the LWAP, but it is not joining.

The WLC IP address is 10.10.10.100, i pasted the log below.

********************************************************************************************** Sending 5, 100-byte ICMP Echos to 10.10.10.100, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms AP0011.21ee.1525# *Mar 1 00:00:34.336: %LWAPP-5-CHANGED: LWAPP changed state to JOIN *Mar 1 00:00:40.337: LWAPP_CLIENT_ERROR_DEBUG: spamHandleJoinTimer: Did not rec ieve the Join response

*Mar 1 00:00:40.337: LWAPP_CLIENT_ERROR_DEBUG: No more AP manager IP addresses remain.

*Mar 1 00:00:40.527: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Re ason: DID NOT GET JOIN RESPONSE. *Mar 1 00:00:40.527: %LWAPP-5-CHANGED: LWAPP changed state to DOWN

*********************************************************************************************************

Your help is higly appreciated Regards Andy

Reply to
Andy

~ Hi guys, i am having a problem with one of the 1200 LWAP to join the ~ controler, i can ping the controler from the LWAP, but it is not ~ joining. ~ ~ The WLC IP address is 10.10.10.100, i pasted the log below. ~ ~ ~

********************************************************************************************** ~ Sending 5, 100-byte ICMP Echos to 10.10.10.100, timeout is 2 seconds: ~ !!!!! ~ Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms ~ AP0011.21ee.1525# ~ *Mar 1 00:00:34.336: %LWAPP-5-CHANGED: LWAPP changed state to JOIN ~ *Mar 1 00:00:40.337: LWAPP_CLIENT_ERROR_DEBUG: spamHandleJoinTimer: ~ Did not rec ~ ieve the Join response ~ ~ *Mar 1 00:00:40.337: LWAPP_CLIENT_ERROR_DEBUG: No more AP manager IP ~ addresses ~ remain. ~ ~ *Mar 1 00:00:40.527: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. ~ Reload Re ~ ason: DID NOT GET JOIN RESPONSE. ~ *Mar 1 00:00:40.527: %LWAPP-5-CHANGED: LWAPP changed state to DOWN ~ ~ ~ ********************************************************************************************************* ~ ~ ~ Your help is higly appreciated ~ Regards ~ Andy

Does the AP1200 have a MIC or an SSC? If the latter, has the SSC been installed in the WLC?

Here are some troubleshooting ideas:

formatting link
Hth,

Aaron

Reply to
Aaron Leonard

Aaron,

Thank you for the document, i am working on it, and i will get back to you once it resolved or not.

Regards, Andy

Reply to
Andy

I entered this command:

(Cisco Controller)>config auth-list add ssc 00:0e:84:32:04:f0 AP_Key

And the AP key you can get from the cvs file in the upgrade utility folder.

Regards, Andy

Reply to
Andy

Cabling-Design.com Forums website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.