Cisco Systems

CatOS router on a stick configuration

Hi I'm having an issue setting up a router on a stick configuration with a 4006 running CatOS and a 2621 router. I have...

3 comments posted 16yrs

posted by tony.dixson

3 comments posted 16yrs posted by tony.dixson

NAT and access lists and IP INSPECT

(this is on an 871W router) ip nat inside source static 10.0.0.11 interface Dialer1 is a "catch all" NAT directive that...

0 comments posted 16yrs

posted by jfmezei.spamnot

0 comments posted 16yrs posted by jfmezei.spamnot

ASA5510 unable to talk between ethernet 0/1 and 0/2

All, I have setup ASA5510 and 0/1 and 0/2 were unable talking to each other. Here is the configuration: ethernet 0/0 ou...

1 comments posted 16yrs

posted by mark256789

1 comments posted 16yrs posted by mark256789

IP INSPECT question

I have tried to read up on the IP INSPECT capabilties in IOS. I can see its usefulness for FTP since it has the smarts...

1 comments posted 16yrs

posted by jfmezei.spamnot

1 comments posted 16yrs posted by jfmezei.spamnot

VPN

Outside of scalability, is there a fundamental difference between pix 501 vpn and vpn 3000 concentrator? Thansk in advan...

8 comments posted 16yrs

posted by nobody

8 comments posted 16yrs posted by nobody

Set trunk command on CAT Os 8.4

I am trying to configure vlan access on a 6506 to a specific port. The network connects multiple buildings in a campus...

0 comments posted 16yrs

posted by banditshockey

0 comments posted 16yrs posted by banditshockey

switch vlan question

I'm looking for a solution that will cause a PC or device with known MAC address or possibly range of MAC addresses to...

7 comments posted 16yrs

posted by tdenham735

7 comments posted 16yrs posted by tdenham735

windows 7 64 Bit VPN Client

I just 2 new laptops that are Windows 7 Enterprise 64Bit and need to get them connected to our ASA 5505 for VPN connect...

6 comments posted 16yrs

posted by timpar

6 comments posted 16yrs posted by timpar

c2801 and layer 2 port

Hello Can i get layer 2 port on my c2801? I have flash:c2801-adventerprisek9-mz.124-17.bin and i can't configure int vl...

5 comments posted 16yrs

posted by bart-nospam

5 comments posted 16yrs posted by bart-nospam

pix ver 8 show run scrolls

After upgrading to version 8 while using putty, any command I issue that has more than a page does not stop and just sc...

3 comments posted 16yrs

posted by mikel

3 comments posted 16yrs posted by mikel

Changing access-groups

Hi, Using a C877W-M running 15.0(1)M1 Should I be able to change the access-group on dialer 1 without killing traffic?...

3 comments posted 16yrs

posted by spam

3 comments posted 16yrs posted by spam

Instantiate VPN Connection Remotely

We have an ASA 5505 that we have remote users VPN into. Is it possible for maintainance for me to be able to start up a...

4 comments posted 16yrs

posted by timpar

4 comments posted 16yrs posted by timpar

Pix 501 VPN

I have configured pix 501 vpn over udp. I use vpn client version 5. When I first establish connection, everything works...

2 comments posted 16yrs

posted by nobody

2 comments posted 16yrs posted by nobody

PIX 501 for home use?

My home router finally died. It was a Linksys BEFSX41 which supposedly did SPI, but that model had a terrible reputatio...

14 comments posted 16yrs

posted by galt_57

14 comments posted 16yrs posted by galt_57

Cisco PIX 515E Configuration

I have a 515E at home, its got a DSL router on its outside interface, my desktop machine on its inside interface and a...

2 comments posted 16yrs

posted by die.spam

2 comments posted 16yrs posted by die.spam