Ethernet LAN

Jumbo Frames - over cross-over cable, and over GigE switch

Hi, I was talking to someone yesterday about some testing that I've been doing with between a pair of computers with In...

6 comments posted 21yrs

posted by ohaya

6 comments posted 21yrs posted by ohaya

Fiber Cable Forsale (Pennies on the Dollar)

I have a number of Fiber Rolls and patch cables with SC,ST and etc... I have a large amount of cable. Call 919 641-7335...

1 comments posted 21yrs

posted by PatrickBrunson

1 comments posted 21yrs posted by PatrickBrunson

data transmissoin system design

Hello, I am in need of some comm system advice...... I need to design a data communications system and I have limited p...

0 comments posted 21yrs

posted by g

0 comments posted 21yrs posted by g

Seeking a clarification on part of RFC 2236 (IGMPv2)

At the bottom of page 5 of RFC 2236, it says that when a Querier receives a Leave, it sends [Last Member Query Count] g...

1 comments posted 21yrs

posted by cnelson

1 comments posted 21yrs posted by cnelson

Network Cabling & Wall Plugs

Hi I've run some cat5 down my house and I need to put rj45 wall plugs on each end... I have the plugs, but it's incredi...

3 comments posted 21yrs

posted by dangelovich

3 comments posted 21yrs posted by dangelovich

bridged ethernet on Dlink router

Hi All I need to configue bridged ethernet between 2 Dlink 1500 G SDSL routers , I couldn't find anything about it. Can...

0 comments posted 21yrs

posted by i.basheer

0 comments posted 21yrs posted by i.basheer

Suggestion for an ethernet setup?

At the moment, I've got 2 workgroups consisting of 5 computers connected via CAT5 cable to a hub which is connected to...

2 comments posted 21yrs

posted by Jameson

2 comments posted 21yrs posted by Jameson

A question about 802.1d based CoS

Hi, I hava a switch Support 802.d layer two based CoS (can set each port for 0-7 priorty. in fact it map to four queues...

3 comments posted 21yrs

posted by aaabbb16

3 comments posted 21yrs posted by aaabbb16

IGMP routing startup

I'm trying to understand how an IGMP router gets started. It _seems_ to me that there's a state transition missing in R...

0 comments posted 21yrs

posted by cnelson

0 comments posted 21yrs posted by cnelson

Network Time (Newbie Q)

We have a network of about 20 computers on a domain - all running WinXP or 2k. The owner has asked about synchronizing...

5 comments posted 21yrs

posted by neorubicant

5 comments posted 21yrs posted by neorubicant

Wither simple ethernet-ethernet routers?

We are a small shop that has two locations currently connected by a pair of cisco 1601 (ethernet/serial only) routers d...

4 comments posted 21yrs

posted by stutzman

4 comments posted 21yrs posted by stutzman

Achieved ~Gigabit on tests - now what?

Hi, Per a post that I just made, I was finally able to configure several network test tools that that I've been using t...

0 comments posted 21yrs

posted by ohaya

0 comments posted 21yrs posted by ohaya

Magnetic-less 1GB ethernet

Hi, I have a design where I need to connect two 1Gb Ethernet devices on one card. To save space & cost I want to capaci...

2 comments posted 21yrs

posted by shw

2 comments posted 21yrs posted by shw

Multicast test bed

I'm trying to learn something about multicasting. I've read up on IGMP, multicast addressing, etc. but I'd like to _see...

1 comments posted 21yrs

posted by cnelson

1 comments posted 21yrs posted by cnelson

About CAT-5 for 2 phone line and ethernet

Hello, I am praveen Kumar. I have a problem in CAT-5, can you please give a feedback. I am planning to use CAT-5 cable...

11 comments posted 21yrs

posted by praveenkumar1979

11 comments posted 21yrs posted by praveenkumar1979