Cisco ASA 5505 configuration for PPPOE/BellSouth

Hello all, I just purchased a Cisco ASA 5505 and I am having trouble configuring my device to work with my BellSouth DSL connection. I tried placing the Netopia 3347NWG in what's called bridge mode but then configure the 5505 for PPPOE but authentication continued to fail. Now I am going to try PPPoE with a Routed Subnet, using the instructions from the Netopia link below

formatting link
I am including my current 5505 conf for your viewing. Any help or advice would be greatly appreciated.


hostname JASZLINK-5505 domain-name enable password xxxxx encrypted names name DC01 description Doman Controller name Dev01 description Development Server name Exchange01 description Exchange Server name Project01 description Project Server ! interface Vlan1 description Inside Network Interface nameif inside/LAN security-level 100 ip address ! interface Vlan2 description Outside Network Interface nameif outside/WAN security-level 0 ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! passwd 2KFQnbNIdI.2KYOU encrypted ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name same-security-traffic permit inter-interface same-security-traffic permit intra-interface access-list inbound extended permit tcp any host Exchange01 eq smtp access-list inbound extended permit tcp any host DC01 eq 3389 access-list inbound extended permit tcp any host DC01 eq pptp access-list inbound extended permit tcp any host Dev01 eq 5904 pager lines 24 logging enable logging asdm informational mtu inside/LAN 1500 mtu outside/WAN 1500 ip verify reverse-path interface outside/WAN no failover icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-522.bin no asdm history enable arp timeout 14400 nat (inside/LAN) 1 static (inside/LAN,outside/WAN) DC01 netmask static (inside/LAN,outside/WAN) Exchange01 netmask static (inside/LAN,outside/WAN) Dev01 netmask static (inside/LAN,outside/WAN) Project01 netmask access-group inbound in interface outside/WAN timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp- pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip- disconnect 0:02:00 timeout uauth 0:05:00 absolute http server enable http inside/LAN no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd update dns ! dhcpd address 10.1.1.x-10.1.1.x inside/LAN dhcpd dns interface inside/LAN dhcpd enable inside/LAN ! dhcpd dns interface outside/WAN !

! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp

prompt hostname context Cryptochecksum:xxxxx : end

Reply to
Loading thread data ...

Hello, when you have a routed subnet you must set the default route /for the internet/. So I don't can see your routing information.

Reply to

Hi here is the example of the pix501 (not asa) config with BellSouth DSL

PIX Version 6.3(5)125 ip address outside pppoe setroute vpdn group bellsouth request dialout pppoe vpdn group bellsouth localname vpdn group bellsouth ppp authentication pap vpdn username password ********* store-local

you probable need to adjust config for asa a little

hope that helped Roman Nakhmanson

Reply to
nakhmanson Forums website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.