Nortel Networks

Upgrade Nortel 470 24/48 stand alone or Stack Error!!!!!

Hello, i'm an administrator of one enormous wan. We have one enormous amount of nortel 470 to upgrade the ver to the 3....

0 comments posted 18yrs

posted by kucio_2000

0 comments posted 18yrs posted by kucio_2000

m7310 and hunt groups

We have a Nortel system with an M7310 admin set. Half of our phones ring when an incoming call comes in. The other half...

1 comments posted 18yrs

posted by yaktam

1 comments posted 18yrs posted by yaktam

Contivity and static NAT

I have 3 servers on an internal network that I need to make visible on the Internet (port 80). I have a Contivity 1010...

2 comments posted 18yrs

posted by dcfindlay

2 comments posted 18yrs posted by dcfindlay

Contivity 1750 Software versions + upgrading

Can anyone tell me what software revisions they are running on their 1750's and if they have upgraded the firmware or so...

0 comments posted 18yrs

posted by SKAY

0 comments posted 18yrs posted by SKAY

Contivity 1750 logging slowness in forewall rules

Hi all we have 2 C 1750's and with only 19 rules in the firewall when we turn logging on the box tends to slow all conn...

0 comments posted 18yrs

posted by SKAY

0 comments posted 18yrs posted by SKAY

lost line 1 on 8x24 system

I have a Meridian 8x24-DS system that I lost access to Line 1. I have tone at the terminal block feeding the connector...

4 comments posted 18yrs

posted by gtslabs

4 comments posted 18yrs posted by gtslabs

Contivity 600 - Internal addresses cannot connect to external address of internal servers

Hi, We have a Contivity 600 that has been working well for many years. Since this morning, we cannot access internal se...

0 comments posted 18yrs

posted by reply

0 comments posted 18yrs posted by reply

Nortel 460-24T PWR, how to make it just into a non addressed switch?

Hello everyone, I've got a Nortel 460-24T PWR switch. Right now it is addressed as: 172.16.34.1 with a subnet of 255.25...

1 comments posted 18yrs

posted by pauly814

1 comments posted 18yrs posted by pauly814

My Call Pilot 4 & Message Forwarding rule

Has anyone had any experience with MyCall Pilot and the message forwarding rule, we've got it setup and working so that...

0 comments posted 18yrs

posted by perchalu

0 comments posted 18yrs posted by perchalu

How could a landline be re-routed?

this happened to me.. i kept getting calls from one phone number always at times i was not home. i kept trying it for m...

0 comments posted 18yrs

posted by mothman20052002

0 comments posted 18yrs posted by mothman20052002

Problem with DN 88XX through ACD

Hi, I have a BCM running version 4.0 with CallPilot. I have realised that I have a problem dialling some DNs once in th...

0 comments posted 18yrs

posted by NOSPAMMarc.Burling

0 comments posted 18yrs posted by NOSPAMMarc.Burling

polycom bridge

Does anyone know what is the procedure to test the polycom bridge with the cisco VT advantage? Thanks, P

1 comments posted 18yrs

posted by priyati09

1 comments posted 18yrs posted by priyati09

System ID CallPilot 100

We are trying to find the system id for a CallPilot 100. The default ip address must have been changed by someone, so w...

1 comments posted 18yrs

posted by nortel

1 comments posted 18yrs posted by nortel

Connecting BCM 400 and BCM 200 together through VoIP trunk

I'm looking for some information on what can and cannot be done with the BCM200/400 system. We have two offices. One ha...

3 comments posted 18yrs

posted by shahidsheikh10

3 comments posted 18yrs posted by shahidsheikh10

Reset Tasman 1450 router to factory default

Newbie here. We recently purchased a used Tasman 1450 router and I need to reset this unit to factory default. I've che...

0 comments posted 18yrs

posted by thilton19

0 comments posted 18yrs posted by thilton19