Latest threads in Ethernet LANshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
RS232 over Ethernet
I have some remote devices with RS232 ports that normally have modems on them to allow remote control over a regular dial up phone line. It uses proprietary software that expects to either see a...
6
|
19 years ago
|
6 | |
|
Best Ethernet switch device for trunking support??
Hi, I am in embedded R&D, and am looking for a Fast Ethernet switch with really good trunking (link aggregation, LAG, etc.) support. If I have a trunk group with 3 ports, than this is what I am...
7
|
19 years ago
|
7 | |
|
XGMII end of packet
Hi, Can any one please clear my understanding about the xgmii end of packet detection. The IEEE draft P802.3ae.pdf XGMII(RS): section 46.2.5 defines the end of packet as "last sequential data octet...
1
|
19 years ago
|
1 | |
|
Safety insulation requirement ethernet
Hello, According to the IEEE std 802.3-2002 section two, the electrical separation shall withstand the following electrical strengt test: - 1500Vrms at 50-60Hz for 60sec, applied as specified in...
2
|
19 years ago
|
2 | |
|
Using Jumbo packets in gigabit ethernet
I have MV64360 Marvell board and I try to send Jumbo frames. I configured the Port Serial Control Register to support Jumbo frames. When I send block in length up to 1500 bytes it works, more then...
4
|
19 years ago
|
4 | |
|
Need Switch Recommendation
I'm looking at co-locating some servers and I need a bit of advice. I need a recommendation for a switch to sit between 8 servers and a 10 Mbps ethernet port to the internet. The switch should be able...
3
|
19 years ago
|
3 | |
|
How is 1000Mbs achieved on 1000BASE-T?
I'm trying to understand how 1Gbs is achieved on Category 5e cabling using a 1000BASE-T. This Dell document reads: "1000BaseT physical layer standard provides 1 Gbps Ethernet signal transmission over...
3
|
19 years ago
|
3 | |
|
MAC address of wireless access point
I am in a setting where there are multiple wireless access points but they are L2 bridged and are on the same IP subnet. How do I find out which access point, i.e. the MAC address of that AP, that I...
5
|
19 years ago
|
5 | |
|
need help to configure, Ascend MX18-8BRIU for ISDN BRI-U on Cisco please?
can anyone assist me to configure this Ascend MAX MX18-8BRIU, I need to get it to work with 2 cisco 2620 routers, with bri-u interfaces in them Thanks please email me back at
—
|
19 years ago
|
— | |
|
MII SFD detection
Hi, I want to know exactly how the SFD detection algorithm works for MII MAC receiver.
14
|
19 years ago
|
14 | |
|
installing software to a server
Hi I am trying to write a 'friendly setup program for some software I have written. Can anyone answer this question for me: When you install software to a server do you run the setup program on the...
5
|
19 years ago
|
5 | |
|
SSMII spec
Hello , PLease let me know where I can get the spec for SSMII.
4
|
19 years ago
|
4 | |
|
performance parameters of Ethrnet packet std IEEE 802.3
Hello all, I have a query regarding gigabit ethernet performance monitoring. I am working on a an application wherein an incoming stream of gigabit ethernet packets is groomed and converted into 8...
—
|
19 years ago
|
— | |
|
Problem with DFE-855 link locking up
I am about to jump on board with someone that has an ongoing problem. Two buildings connected by fiber and D-Link DFE-855 media converters on each end. Both DFE-855 units connect to 3Com 16-port hubs...
2
|
19 years ago
|
2 | |
|
Netgear WGT624 V2 Router
I finally bought myself a Netgear WGT624 V2 Router. And I have to say I am somewhat disappointed. Whilst everything works. I cant say it works for any length of time. If I have the wireless feature...
3
|
19 years ago
|
3 |