Ethernet LAN

elements of a networking appplication

what all can be the elements of a networking appplication this is required for my proj and to understand its scope.

2 comments posted 18yrs

posted by adhicalling

2 comments posted 18yrs posted by adhicalling

Monitor traffic through router?

Is it possible to monitor traffic through the local router on a 10/100 ethernet network? For example, the Netgear wrt61...

3 comments posted 18yrs

posted by reply

3 comments posted 18yrs posted by reply

Gigabit throughput tests?

What's a simple way to test a LAN for throughput after upgrading to gigabit? (Cat5e cables, switch, patch panel, and pa...

11 comments posted 18yrs

posted by incognito

11 comments posted 18yrs posted by incognito

Patch panel in small business?

Is there any advantage to using a patch panel in a gigabit ethernet network? I'm pulling all new cables for less than 2...

33 comments posted 18yrs

posted by incognito

33 comments posted 18yrs posted by incognito

Gbps practical performance?

Hi all, >From what I know, the the nature of CSMA/CD limits the practical performance on a ethernet network. If I remem...

2 comments posted 18yrs

posted by anders.newsonly

2 comments posted 18yrs posted by anders.newsonly

Difference between bridge and wireless access point??

A bridge connects two different network segments (different IP address network portion) together? Whereas a Access poin...

7 comments posted 18yrs

posted by fordgwf

7 comments posted 18yrs posted by fordgwf

switch for troubleshooting

For many years I carried around a small 4 port 10base-t hub that I used for troubleshooting. I would hook my laptop to...

0 comments posted 18yrs

posted by j.wuenschell

0 comments posted 18yrs posted by j.wuenschell

how fast is a 1Gbps lan?

I have Comcastmodem by scientific alanta to Linksys router WRTS4G --- lan1 to SonicWall TZ170 100Mbps to 1Gbps Netgear...

0 comments posted 18yrs

posted by rick0.merrill

0 comments posted 18yrs posted by rick0.merrill

Layer 2 switch vs Layer 3 switch

Hello, I would just like to confirm. If I want to setup VLANS using a Layer 2 switch, I would also require a router to...

2 comments posted 18yrs

posted by ramcneilly

2 comments posted 18yrs posted by ramcneilly

Seeing Packets on an Ethernet Port That Should Not Be There

Let's say that we have three IPs on the same subnet, each IP belongs to one computer, and each IP corresponds to one po...

1 comments posted 18yrs

posted by westes-usc

1 comments posted 18yrs posted by westes-usc

Is Ethernet The Right Solution For Your Data Network?

This is not a trivial question. Ethernet is relatively ubiquitous, in that most computers and peripherals speak etherne...

1 comments posted 18yrs

posted by melemm

1 comments posted 18yrs posted by melemm

Question about MII (Media Independent Interface) in PHY

Hi, I've implemented an Ethernet driver based upon some example code we received from a parts vendor. This driver is ru...

5 comments posted 18yrs

posted by rf1ler

5 comments posted 18yrs posted by rf1ler

Plugging nodes into a switch while nodes are powered on

While reading through a networking book (that shall for the time being remain nameless) I came accross a dictum that I...

1 comments posted 18yrs

posted by Nonapeptide

1 comments posted 18yrs posted by Nonapeptide

VLANS and subnetting

Hi all. I am new to VLAN's. I have a requirement, and I want to know whether it is technically possible to do. I have a...

10 comments posted 18yrs

posted by tech.support.b

10 comments posted 18yrs posted by tech.support.b

connecting Cisco router to Juniper router via e1

hello. Does any1 knows how to connect Cisco router to Juniper router via e1. I have juniper's 2300 , and Cisco's 2600 w...

1 comments posted 18yrs

posted by timgold81

1 comments posted 18yrs posted by timgold81