Hi, newbie again... I am having issues getting my PIX 506e to allow internet access. I cannot ping from the inside interface to the outside interface or gateway, even after opening up ICMP. I have two internal subnets: 1.0.0.0 and 192.168.2.0. The 192.168.2.0 passes through a Win2K box set up for routing (1.0.0.241). The configuration is as follows:
PIX Version 6.3(5) interface ethernet0 auto interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password ############ encrypted passwd ############# encrypted hostname pixfirewall domain-name xxxxxxxxxxxxxx.com fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 names access-list outside_access_in remark E-mail inbound access-list outside_access_in permit tcp interface outside eq smtp host
1.0.0.241 eq smtp access-list outside_access_in remark FTP Site access-list outside_access_in permit tcp interface outside eq ftp host 192.168.2.22 eq ftp access-list outside_access_in remark HTTP Sites access-list outside_access_in permit tcp interface outside eq www host 1.0.0.241 eq www access-list outside_access_in remark RDP access to terminal server access-list outside_access_in permit tcp interface outside eq 33389 host 1.0.0.244 eq 33389 access-list outside_access_in permit udp any eq domain any access-list inside_access_in remark Default Rule access-list inside_access_in permit tcp interface inside interface outside access-list inside_access_in remark Default UDP Rule access-list inside_access_in permit udp interface inside interface outside pager lines 24 logging on mtu outside 1500 mtu inside 1500 ip address outside xxx.xxx.xxx.117 255.255.255.248 ip address inside 1.0.0.3 255.0.0.0 ip verify reverse-path interface outside ip audit info action alarm ip audit attack action alarm pdm location 192.168.1.0 255.255.255.0 inside pdm location 1.0.0.241 255.255.255.255 inside pdm location 1.0.0.244 255.255.255.255 inside pdm location 192.168.2.22 255.255.255.255 inside pdm location 192.168.2.0 255.255.255.0 inside pdm logging informational 100 pdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 192.168.2.22 255.255.255.255 0 0 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 static (inside,outside) 1.0.0.241 1.0.0.241 netmask 255.255.255.255 0 0static (inside,outside) 1.0.0.244 1.0.0.244 netmask 255.255.255.255 0 0
access-group outside_access_in in interface outside access-group inside_access_in in interface inside rip inside default version 1 route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1 route inside 192.168.2.0 255.255.255.0 1.0.0.241 1 route inside 192.168.2.22 255.255.255.255 1.0.0.241 1 timeout xlate 0:05:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225
1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout sip-disconnect 0:02:00 sip-invite 0:03:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server TACACS+ max-failed-attempts 3 aaa-server TACACS+ deadtime 10 aaa-server RADIUS protocol radius aaa-server RADIUS max-failed-attempts 3 aaa-server RADIUS deadtime 10 aaa-server LOCAL protocol local http server enable http 1.0.0.0 255.0.0.0 inside no snmp-server location no snmp-server contact snmp-server community public no snmp-server enable traps floodguard enable telnet timeout 5 ssh timeout 5 console timeout 0 terminal width 80 Cryptochecksum:xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx : end [OK]I'm sure this is obvious, but help please...I suspect a routing issue, but the routing table seems ok. Second, as you can see I am trying to make available certain services to Internet users...just want to verify accuracy of commands.
Thanks...