D-Link DWL-2100AP user guide: System Settings

System Settings

You can customize the basic System Settings for the DWL-2100AP by clicking on this button.

Access Password: This sets the admin password for the select device(s).

Auto Refresh: This setting allows you to enable auto refreshing of the network device list. By default this option is disabled. If you choose to enable it, you must enter the refresh interval in seconds. All other settings on this screen should be left at the default setting.

Setup Wizard

This button will launch the Setup Wizard that will guide you through device configuration.

Enter a Password and retype it in the Verify Password field.

Click Next.

DWL-2100AP User Manual 78

DWL-2100AP Setup Wizard

Enter the SSID and the Channel for the IEEE network.

Auto Channel Scan is enabled by default. The access point will scan for the best available channel.

Click Next.

If you want to enable Encryption, enter the Encryption values here.

Click Next.

DWL-2100AP User Manual 79

If you selected WEP, select the key size (64, 128, or 152-bit), the key type (HEX or ASCII), and then enter your WEP key.

Click Next.

If you selected WPA-Personal (PSK), enter the passphrase.

Cipher Type TKIP is used. 1800 for Group Key Update Interval is suggested.

Click Next.

DWL-2100AP User Manual 80

The DWL-2100AP setup is complete!

DWL-2100AP User Manual 81

Refresh

Click on this button to refresh the list of devices available on the network.

Devices with a checkmark next to them are still available on the network. Devices with an X are no longer available on the network.

About

Click on this button to view the version of AP Manager.

Networking Basics

Using the Network Setup Wizard in Windows® XP

In this section you will learn how to establish a network at home or work, using Microsoft Windows® XP.

Note: Please refer to websites such as http://www.homenethelp.com and http://www.microsoft.com/windows2000 for information about networking computers using Windows® 2000.

Go to Start>Control Panel>Network Connections Select Set up a home or small office network

When this screen appears, click Next.

Please follow all the instructions in this window:

Click Next.

In the following window, select the best description of your computer. If your computer connects to the internet through a gateway/router, select the second option as shown.

Click Next.

DWL-2100AP User Manual 84

Enter a Computer description and a Computer name (optional).

Click Next.

Enter a Workgroup name. All computers on your network should have the same Workgroup name.

Click Next.

DWL-2100AP User Manual 85

Please wait while the Network Setup Wizard applies the changes.

When the changes are complete, click Next.

Please wait while the Network Setup Wizard configures the computer. This may take a few minutes.

In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next.

Insert a disk into the Floppy Disk Drive, in this case drive A.

Click Next.

DWL-2100AP User Manual 87

Please read the information under Here's how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue click Next.

DWL-2100AP User Manual 88

Please read the information on this screen, then click Finish to complete the Network Setup Wizard.

The new settings will take effect when you restart the computer. Click Yes to restart the computer.

You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. After running the Network Setup Disk on all your computers, your new wireless network will be ready to use.

DWL-2100AP User Manual 89

Naming Your Computer

To name your computer in Windows® XP, please follow these directions.

■ Click Start (in the lower left corner of the screen).

■ Right-click on My Computer.

■ Select Properties and click.

■ Select the Computer Name Tab in the System Properties window.

■ You may enter a Computer Description if you wish; this field is optional.

■ To rename the computer and join a domain, Click Change.

DWL-2100AP User Manual 90

• In this window, enter the Computer name.
• Select Workgroup and enter the name of the Workgroup.
• All computers on your network must have the same Workgroup name.
• Click OK.

Checking the IP Address in Windows® XP

The wireless adapter-equipped computers in your network must be in the same IP Address range (see Getting Started in this manual for a definition of IP Address Range.) To check on the IP Address of the adapter, please do the following:

• Right-click on the Local Area Connection icon in the task bar.
• Click on Status.

Disable Status Repair View Available Wireless Networks Open Network Connections 3:05 PM

DWL-2100AP User Manual 91

This window will appear:

■ Click the Support tab.

■ Click Close.

DWL-2100AP User Manual 92

Assigning a Static IP Address in Windows® XP/2000

Note: DHCP-enabled routers will automatically assign IP addresses to the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology. If you are using a DHCP-capable router you will not need to assign static IP addresses.

If you are not using a DHCP capable router, or you need to assign a static IP address, please follow these instructions:

■ Go to Start.

■ Double-click on Control Panel.

■ Double-click on Network Connections.

DWL-2100AP User Manual 93

■ Right-click on Local Area Connections.

■ Double-click on Properties.

■ Click on Internet Protocol (TCP/IP).

■ Click Properties.

■ Input your IP address and subnet mask. (The IP addresses on your network must be within the same range. For example, if one computer has an IP address of 192.168.0.2, the other computers should have IP addresses that are sequential, like 192.168.0.3 and 192.168.0.4. The subnet mask must be the same for all the computers on the network.)

DWL-2100AP User Manual 94

• Input your DNS server addresses. Note: If you are entering a DNS server, you must enter the IP address of the default gateway.

The DNS server information will be supplied by your ISP (Internet Service Provider.)

• Click OK.

Assigning a Static IP Address in Macintosh® OSX

• Go to the Apple Menu and select System Preferences.
• Click on Network.

\blacksquare Select Built-in Ethernet in the Show pull-down menu.

\blacksquare Select Manually in the Configure pull-down menu.

\blacksquare Input the Static IP Address, the Subnet Mask and the Router IP Address in the appropriate fields.

\blacksquare Click Apply Now.

DWL-2100AP User Manual 96

\blacksquare Go to the Apple Menu and select System Preferences.

\blacksquare Click on Network.

\blacksquare Select Built-in Ethernet in the Show pull-down menu.

\blacksquare Select Using DHCP in the Configure pull-down menu.

DWL-2100AP User Manual 97

• Click Apply Now.
• The IP Address, Subnet mask, and the Router’s IP Address will appear in a few seconds.

Checking the Wireless Connection by Pinging in Windows® XP and 2000

Go to Start > Run > type cmd. A window similar to this one will appear. Type ping xxx.xxx.xxx.xxx, where xxx is the IP address of the wireless router or access point. A good wireless connection will show four replies from the wireless router or access point, as shown.

Troubleshooting

This Chapter provides solutions to problems that can occur during the installation and operation of the DWL-2100AP Wireless Access Point. We cover various aspects of the network setup, including the network adapters. Please read the following if you are having problems.

Note: It is recommended that you use an Ethernet connection to configure the DWL-2100AP.

1. The computer used to configure the DWL-2100AP cannot access the Configuration menu.

■ Check that the Ethernet LED on the DWL-2100AP is ON. If the LED is not ON, check that the cable for the Ethernet connection is securely inserted.

■ Check that the Ethernet Adapter is working properly. Please see item 3 (Check that the drivers for the network adapters are installed properly) in this Troubleshooting section to check that the drivers are loaded properly.

■ Check that the IP address is in the same range and subnet as the DWL-2100AP. Please see Checking the IP Address in Windows® XP in the Networking Basics section of this manual.

Note: The IP address of the DWL-2100AP is 192.168.0.50. All the computers on the network must have a unique IP address in the same range, e.g., 192.168.0.x. Any computers that have identical IP addresses will not be visible on the network. They must all have the same subnet mask, e.g., 255.255.255.0.

■ Do a Ping test to make sure that the DWL-2100AP is responding. Go to Start>Run>Type Command>Type ping 192.168.0.50. A successful ping will show four replies.

Note: If you have changed the default IP address, make sure to ping the correct IP address assigned to the DWL-2100AP.

DWL-2100AP User Manual 99

2. The wireless client cannot access the Internet in the Infrastructure mode.

Make sure the wireless client is associated and joined with the correct access point. To check this connection: Right-click on the Local Area Connection icon in the taskbar> select View Available Wireless Networks. The Connect to Wireless Network screen will appear. Please make sure you have selected the correct available network, as shown in the illustrations below.

■ Check that the IP address assigned to the wireless adapter is within the same IP address range as the access point and gateway. Since the DWL-2100AP has an IP address of 192.168.0.50, wireless adapters must have an IP address in the same range, e.g., 192.168.0.x. Each device must have a unique IP address; no two devices may have the same IP address. The subnet mask must be the same for all the computers on the network.) To check the IP address assigned to the wireless adapter, double-click on the Local Area Connection icon in the taskbar > select the Support tab and the IP address will be displayed. Please refer to Checking the IP Address in the Networking Basics section of this manual.)

■ If it is necessary to assign a Static IP Address to the wireless adapter, please refer to the appropriate section in Networking Basics. If you are entering a DNS Server address you must also enter the Default Gateway Address. (Remember that if you have a DHCP-capable router, you will not need to assign a static IP address. See Networking Basics: Assigning a Static IP Address.)

DWL-2100AP User Manual 100

3. Check that the drivers for the network adapters are installed properly.

You may be using different network adapters than those illustrated here, but this procedure will remain the same, regardless of the type of network adapters you are using.

■ Go to Start > My Computer > Properties.

■ Select the Hardware Tab.

■ Click Device Manager.

DWL-2100AP User Manual 101

• Double-click on Network Adapters.
• Right-click on D-Link AirPlus DWL-G680 Wireless Cardbus Adapter. (In this example we use the DWL-G680; you may be using other network adapters, but the procedure will remain the same.)
• Select Properties to check that the drivers are installed properly.

• Look under Device Status to check that the device is working properly.
• Click OK.

4. What variables may cause my wireless products to lose reception?

D-Link products let you access your network from virtually anywhere you want. However, the positioning of the products within your environment will affect the wireless range. Please refer to Installation Considerations in the Wireless Basics section of this manual for further information about the most advantageous placement of your D-Link wireless products.

5. Why does my wireless connection keep dropping?

■ Antenna Orientation- Try different antenna orientations for the DWL-2100AP. Try to keep the antenna at least 6 inches away from the wall or other objects.

■ If you are using 2.4GHz cordless phones, X-10 equipment or other home security systems, ceiling fans, and lights, your wireless connection will degrade dramatically or drop altogether. Try changing the channel on your router, access point and wireless adapter to a different channel to avoid interference.

■ Keep your product away (at least 3-6 feet) from electrical devices that generate RF noise, like microwaves, monitors, electric motors, etc.

6. Why can’t I get a wireless connection?

If you have enabled encryption on the DWL-2100AP, you must also enable encryption on all wireless clients in order to establish a wireless connection.

■ Make sure that the SSID on the router and the wireless client are exactly the same. If they are not, wireless connection will not be established.

■ Move the DWL-2100AP and the wireless client into the same room and then test the wireless connection.

■ Disable all security settings.

■ Turn off your DWL-2100AP and the client. Turn the DWL-2100AP back on again, and then turn on the client.

■ Make sure that all devices are set to Infrastructure mode.

■ Check that the LED indicators are indicating normal activity. If not, check that the AC power and Ethernet cables are firmly connected.

■ Check that the IP address, subnet mask, gateway and DNS settings are correctly entered for the network.

■ If you are using 2.4GHz cordless phones, X-10 equipment or other home security systems, ceiling fans, and lights, your wireless connection will degrade dramatically or drop altogether. Try changing the channel on your DWL-2100AP, and on all the devices in your network to avoid interference.

■ Keep your product away (at least 3-6 feet) from electrical devices that generate RF noise, like microwaves, monitors, electric motors, etc.

7. I forgot my encryption key.

■ Reset the DWL-2100AP to its factory default settings and restore the other devices on your network to their default settings. You may do this by pressing the Reset button on the back of the unit. You will lose the current configuration settings.

Technical Specifications

Standards

• IEEE 802.11b
• IEEE 802.11g
• IEEE 802.3
• IEEE 802.3u
• IEEE 802.3x

Network Management

• Web Browser interface
• AP Manager
• SNMP v.3
• Telnet

Data Rate*

For 802.11b:

• 11, 5.5, 2, and 1Mbps

For 802.11g:

• 108, 54, 48, 36, 24, 18, 12, 9 and 6Mbps

Security

• 64/128/152-bit WEP
• WPA (Wi-Fi Protected Access) - TKIP/AES/PSK
• MAC Address Access Control List

Wireless Frequency Range

• 2.4GHz to 2.4835GHz

Radio and Modulation Type

For 802.11b: DSSS:

• DBPSK @ 1Mbps
• DQPSK @ 2Mbps
• CCK @ 5.5 and 11Mbps

For 802.11g: OFDM:

• BPSK @ 6 and 9Mbps
• QPSK @ 12 and 18Mbps
• 16QAM @ 24 and 36Mbps
• 64QAM @ 48 and 54Mbps

DSSS:

• DBPSK @ 1Mbps
• DQPSK @ 2Mbps
• CCK @ 5.5 and 11Mbps

Receiver Sensitivity

For 802.11b:

• 1Mbps: -94dBm
• 2Mbps: -90dBm
• 5.5Mbps: -88dBm
• 11Mbps: -85dBm

For 802.11g:

• 1Mbps: -94dBm
• 2Mbps: -91dBm
• 5.5Mbps: -89dBm
• 6Mbps: -91dBm
• 9Mbps: -90dBm
• 11Mbps: -86dBm
• 12Mbps: -89dBm
• 18Mbps: -87dBm
• 24Mbps: -84dBm
• 36Mbps: -80dBm
• 48Mbps: -76dBm
• 54Mbps: -73dBm

Transmit Output Power

Typical RF Output Power at each Data Rate:

For 802.11b:

• 31mW (15dBm) @ 54 and 108Mbps
• 40mW (16dBm) @ 48Mbps
• 63mW (18dBm) @ 36, 24, 18, 12, 9, and 6Mbps

For 802.11g:

• 63mW (18dBm) @ 11, 5.5, 2, and 1Mbps

Wireless Operating Range*

802.11g (Full Power with 2dBi gain diversity dipole antenna)

Indoor:

• 98ft (30m) @ 54Mbps
• 105ft (32m) @ 48Mbps
• 121ft (37m) @ 36Mbps
• 148ft (45m) @ 24Mbps
• 197ft (60m) @ 18Mbps
• 223ft (68m) @ 12Mbps
• 253ft (77m) @ 9Mbps
• 295ft (90m) @ 6Mbps

Outdoor:

• 312ft (95m) @ 54Mbps
• 951ft (290m) @ 11Mbps
• 1378ft (420m) @ 6Mbps

Operating Voltage

• 5VDC +/- 10%

LEDs

• Power
• 10M/100M
• WLAN

*Maximum wireless signal rate derived from IEEE Standard 802.11g specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range.

DWL-2100AP User Manual 105

Temperature • Operating: -32°F to 104°F (0°C to 40°C) • Storing: -4°F to 149°F (-20°C to 65°C)

Humidity • Operating: 10%~90% (non-condensing) • Storing: 5%~95% (non-condensing)

Certifications • FCC Part 15 • CSA • UL • Wi-Fi

Dimensions • L = 5.59 inches (142mm) • W = 4.29 inches (109mm) • H = 1.22 inches (31mm)

Warranty • 3 Years

Technical Support

You can find software updates and user documentation on the D-Link website.

D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product.

U.S. and Canadian customers can contact D-Link Technical Support through our website, or by phone.

Tech Support for customers within the United States: D-Link Technical Support over the Telephone: (877) 453-5465 24 hours a day, seven days a week

D-Link Technical Support over the Internet: http://support.dlink.com

Tech Support for customers within Canada: D-Link Technical Support over the Telephone: (800) 361-5265 Monday to Friday 7:30am to 9:00pm EST

D-Link Technical Support over the Internet: http://support.dlink.ca

Warranty

Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:

• Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and
• Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.

Limited Warranty: D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except as otherwise stated herein.

• Hardware (excluding power supplies and fans): One (1) year
• Power supplies and fans: One (1) year
• Spare parts and spare kits: Ninety (90) days

The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer, and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.

Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional specifications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software

(and all copies thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given automatically terminates.

Non-Applicability of Warranty: The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.

Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:

• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist the customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.com/.
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer.

D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.

What Is Not Covered: The Limited Warranty provided herein by D-Link does not cover: Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance

DWL-2100AP User Manual 109

or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product. While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.

Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.

Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY.

Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state.

Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective owners.

Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice. Copyright 2005 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.

DWL-2100AP User Manual 110

CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help.

For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link office.

Registration

Register your product online at: http://support.dlink.com/register

Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.

Version 2.0 May 30, 2006