Problems with bonding 2 x SHDSL lines using MLPPP and CISCO1721
Bookmark this page:
 Yahoo!
 Google
 Windows Live
 del.icio.us
 digg
 Netscape
|
|
|||||||||||||
|
Posted by Phil Bartlett on December 14, 2005, 12:38 am
Please log in for more thread options We seem to be having problems with setting up bonding 2 SHDSL 1Mb lines using a CISCO1721 w/ WIC-SHDSL-V2. But it doesn't seem to be working. When we enable both the lines, the service just drops. Our ISP is Freedom to Surf (F2S) and BT is the wholesale provider. We have spoken to F2S and they say that some of the BT exchanges are not set up to support DSL MLPPP. Does anyone have similar experiences or ideas for a solution? any thoughts would be grateful Rgds Phil | |||||||||||||
|
Posted by Erik Semey on December 15, 2005, 11:10 pm
Please log in for more thread options Units in both ends need to use same Bonding type | |||||||||||||
|
Posted by Gary on December 16, 2005, 10:12 pm
Please log in for more thread options
We have had exactly that and opened a TAC case. Normally if the lines are ordered at the same time they go through the same DSLAM etc and timing is OK, but in our case the timing fails. Solution was to avoid MLPPP and uase either multi Home NAT or load sharing with 2 routes G > Units in both ends need to use same Bonding type
> > >>
>> >> >> We seem to be having problems with setting up bonding 2 SHDSL 1Mb lines >> >> using a CISCO1721 w/ WIC-SHDSL-V2. But it doesn't seem to be working. >> When we enable both the lines, the service just drops. Our ISP is >> Freedom to Surf (F2S) and BT is the wholesale provider. We have spoken >> to F2S and they say that some of the BT exchanges are not set up to >> support DSL MLPPP. Does anyone have similar experiences or ideas for a >> solution? >> >> >> any thoughts would be grateful >> >> >> Rgds >> >> >> Phil >> >
> | |||||||||||||
|
Posted by Phil Bartlett on December 23, 2005, 3:17 am
Please log in for more thread options
Well it seems finally Freedom 2 Surf have managed to provide us with 2 x 1Mbs lines bundled together. After plenty of emails/phone calls to and fro them and BT have made the changes to the DSLAM and their network. WEYHEY!! Phil Bartlett wrote: > We seem to be having problems with setting up bonding 2 SHDSL 1Mb lines
> > using a CISCO1721 w/ WIC-SHDSL-V2. But it doesn't seem to be working. > When we enable both the lines, the service just drops. Our ISP is > Freedom to Surf (F2S) and BT is the wholesale provider. We have spoken > to F2S and they say that some of the BT exchanges are not set up to > support DSL MLPPP. Does anyone have similar experiences or ideas for a > solution? > > > any thoughts would be grateful > > > Rgds > > > Phil | |||||||||||||
>
>
> We seem to be having problems with setting up bonding 2 SHDSL 1Mb lines
>
> using a CISCO1721 w/ WIC-SHDSL-V2. But it doesn't seem to be working.
> When we enable both the lines, the service just drops. Our ISP is
> Freedom to Surf (F2S) and BT is the wholesale provider. We have spoken
> to F2S and they say that some of the BT exchanges are not set up to
> support DSL MLPPP. Does anyone have similar experiences or ideas for a
> solution?
>
>
> any thoughts would be grateful
>
>
> Rgds
>
>
> Phil
>