Latest threads in Nortel Networksshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
Meridian Telnet->RS232 login problem
13 characters, huh? What are those 13? You might reconfigure your process to send a return, then "LOGI", another carriage return and then wait for the response "PASS?". Finally send the appropriate...
2
|
16 years ago
|
2 | |
|
Upgrade Nortel 470 24/48 stand alone or Stack Error!!!!!
Hello, i'm an administrator of one enormous wan. We have one enormous amount of nortel 470 to upgrade the ver to the 3.6.5. Reading the news of Nortel on this specific modernization evince that it...
—
|
16 years ago
|
— | |
|
m7310 and hunt groups
We have a Nortel system with an M7310 admin set. Half of our phones ring when an incoming call comes in. The other half do not (tho the little LINE triangle flashes on the silent sets). I thought that...
1
|
16 years ago
|
1 | |
|
Contivity and static NAT
I have 3 servers on an internal network that I need to make visible on the Internet (port 80). I have a Contivity 1010 VPN router and 32 public IP addresses, one of which is taken up by the public...
2
|
16 years ago
|
2 | |
|
Contivity 1750 Software versions + upgrading
Can anyone tell me what software revisions they are running on their 1750's and if they have upgraded the firmware or software on the units. Thanks
—
|
16 years ago
|
— | |
|
Contivity 1750 logging slowness in forewall rules
Hi all we have 2 C 1750's and with only 19 rules in the firewall when we turn logging on the box tends to slow all connections down. the logging is only at the brief level but once we turn all logging...
—
|
16 years ago
|
— | |
|
lost line 1 on 8x24 system
Also, dial Feature *0, then press what you think is line 1. What does the display say then?
4
|
16 years ago
|
4 | |
|
Contivity 600 - Internal addresses cannot connect to external address of internal servers
Hi, We have a Contivity 600 that has been working well for many years. Since this morning, we cannot access internal servers using their external (publicly visible and routable) addresses. For...
—
|
16 years ago
|
— | |
|
Nortel 460-24T PWR, how to make it just into a non addressed switch?
Reset the switch back to factory defaults. At the Command Line Interface, type: boot default Then you may wish to set the ports for fast spanning tree and stop the switch from trying to acquire an...
1
|
16 years ago
|
1 | |
|
My Call Pilot 4 & Message Forwarding rule
Has anyone had any experience with MyCall Pilot and the message forwarding rule, we've got it setup and working so that a user can have their voice mail forwarded to their email inbox (non CallPilot)....
—
|
16 years ago
|
— | |
|
How could a landline be re-routed?
this happened to me.. i kept getting calls from one phone number always at times i was not home. i kept trying it for months until one day i tried it from work. then someone answered it and i heard...
—
|
16 years ago
|
— | |
|
Problem with DN 88XX through ACD
Hi, I have a BCM running version 4.0 with CallPilot. I have realised that I have a problem dialling some DNs once in the ACD. The DNs that are the problem start 88 as the system thinks I want to...
—
|
16 years ago
|
— | |
|
polycom bridge
Does anyone know what is the procedure to test the polycom bridge with the cisco VT advantage? Thanks, P
1
|
16 years ago
|
1 | |
|
System ID CallPilot 100
We are trying to find the system id for a CallPilot 100. The default ip address must have been changed by someone, so we are having a hard time getting into the system via the network port. What are...
1
|
16 years ago
|
1 | |
|
Connecting BCM 400 and BCM 200 together through VoIP trunk
I'm looking for some information on what can and cannot be done with the BCM200/400 system. We have two offices. One has a BCM 400 system and the other has a BCM 200. The two offices are connected...
3
|
16 years ago
|
3 |