New hardware...oh no it isn't!
Bookmark this page:
 Yahoo!
 Google
 Windows Live
 del.icio.us
 digg
 Netscape
|
|
|||||||||||||||||||
|
Posted by Brickcounter on January 29, 2007, 7:34 am
Please log in for more thread options every time I switch the printer on I get the 'Found new hardware' message. I just close it, and the resulting warning, and it works. But how can I stop it showing the new hardware message? On a similar subject I have also installed a wireless card (Netgear WG311T) and wireless modem/router (Netgear DG834GT), and on boot I get the Netgear config wizard every time. Similarly I close this, and it works ok. But again, how can I stop it opening the wizard unnecessarily? brickcounter -- Windows XP Pro SP1 Gigabyte GA-VTXE 1.0 motherboard AMD 1.4 Althon XP processor 1 Gb RAM Radeon 8500 graphics card | |||||||||||||||||||
|
Posted by Gerard Bok on January 29, 2007, 8:50 am
Please log in for more thread options Probably, you didn't (fully) finish the installation. Insert the driver media, go to the device manager, select update driver. And be a little more patient, before you remove the media. (Especially if a reboot is part of the installation procedure.) -- Kind regards, Gerard Bok | |||||||||||||||||||
|
Posted by xorbit on January 29, 2007, 10:09 am
Please log in for more thread options Brickcounter wrote:
> I have recently reinstalled my printer sw, and all works fine, except that
> every time I switch the printer on I get the 'Found new hardware' message. > I just close it, and the resulting warning, and it works. But how can I stop > it showing the new hardware message? > On a similar subject I have also installed a wireless card (Netgear WG311T) > and wireless modem/router (Netgear DG834GT), and on boot I get the Netgear > config wizard every time. Similarly I close this, and it works ok. But > again, how can I stop it opening the wizard unnecessarily? > brickcounter > > -- > Windows XP Pro SP1 > Gigabyte GA-VTXE 1.0 motherboard > AMD 1.4 Althon XP processor > 1 Gb RAM > Radeon 8500 graphics card > > Check to see if your anti-virus is allowing permanent registry changes. | |||||||||||||||||||
|
Posted by Noozer on January 30, 2007, 12:31 am
Please log in for more thread options
>I have recently reinstalled my printer sw, and all works fine, except that
> every time I switch the printer on I get the 'Found new hardware' message. > I just close it, and the resulting warning, and it works. But how can I > stop > it showing the new hardware message? USB printer? Model would help. If USB, did you change the USB port it was connected to? > On a similar subject I have also installed a wireless card (Netgear
> WG311T) > and wireless modem/router (Netgear DG834GT), and on boot I get the Netgear > config wizard every time. Similarly I close this, and it works ok. But > again, how can I stop it opening the wizard unnecessarily? > brickcounter > > -- > Windows XP Pro SP1 > Gigabyte GA-VTXE 1.0 motherboard > AMD 1.4 Althon XP processor > 1 Gb RAM > Radeon 8500 graphics card > > | |||||||||||||||||||
|
Posted by Brickcounter on February 2, 2007, 11:57 am
Please log in for more thread options Noozer found the answer - I had plugged it in a different usb port.
Problem solved. Thanks N. bc >I have recently reinstalled my printer sw, and all works fine, except that
> every time I switch the printer on I get the 'Found new hardware' message. > I just close it, and the resulting warning, and it works. But how can I > stop > it showing the new hardware message? > On a similar subject I have also installed a wireless card (Netgear > WG311T) > and wireless modem/router (Netgear DG834GT), and on boot I get the Netgear > config wizard every time. Similarly I close this, and it works ok. But > again, how can I stop it opening the wizard unnecessarily? > brickcounter > > -- > Windows XP Pro SP1 > Gigabyte GA-VTXE 1.0 motherboard > AMD 1.4 Althon XP processor > 1 Gb RAM > Radeon 8500 graphics card > > > | |||||||||||||||||||
| Similar Threads | Posted |
| hardware | June 29, 2005, 9:36 am |
| Hardware Help | September 26, 2005, 4:22 pm |
| hardware | December 21, 2005, 4:30 pm |
| Hardware | June 27, 2007, 1:19 am |
| All about hardware | December 3, 2006, 1:43 pm |
| Hardware Help | January 25, 2007, 2:19 pm |
| New hardware...oh no it isn't! | January 29, 2007, 7:34 am |
| New Hardware | June 1, 2007, 4:09 pm |
| Hot Hardware | June 3, 2007, 4:38 pm |
| oem hardware? | October 30, 2007, 2:37 pm |
| what hardware?? | February 19, 2008, 11:54 pm |
| vpn hardware | July 11, 2008, 4:17 pm |
| FS Computer Hardware | July 13, 2005, 1:56 am |
| storing old hardware | July 15, 2005, 8:22 am |
| ***WTB NETWORK HARDWARE*** | July 25, 2005, 5:26 pm |
>every time I switch the printer on I get the 'Found new hardware' message.
>I just close it, and the resulting warning, and it works. But how can I stop
>it showing the new hardware message?