Latest threads in Cisco Systemsshow only best voted threads

Subject Author Posted Replies
 
Carrier Ethernet
Hello, they often say, for example that such concepts as "bridge" or "spanning tree" don't scale well to large networks. What exactly is meant here by "scale" ? Thanks. Mark
9
9
 
more detail in IPSEC debugging?
We have several IPSEC tunnels to all kinds of different routers. When I enable "debug crypto ipsec" I get occasional messages like this: IPSEC(epa_des_crypt): decrypted packet failed SA identity check...
4
4
 
Dealing with ACL limitations on Catalyst 2950 switch
I have a Catalyst 2950 switch here running IOS v12 Enhanced Image. As you know (if you have dealt with this particular line), while there is ACL support, it's rather limited. I would like to set an...
 
relation between kernel FIB and hardware FIB
Usually they each maintain separate tables. Each routing protocol typically needs to maintain its own state, because they operate independently -- a RIP route shouldn't normally be advertised via BGP....
3
3
 
interface Opnet and Matlab
Hello all ... please is there any one know how to do interface between Opnet and Matlab I want to do smart antenna with mobile ad hoc network so smart antenna in Matlab and Mobile ad hoc net. in opnet...
1
1
 
spanning tree issue
We have connected 2 cisco switches running pvst+ to 2 non cisco switches(no= rtel) which support pvst in a full mesh topology. cisco1 is root for vlan 1= 0, cisco2 root for vlan20. cisco1----cisco2 |...
 
Problem with cisco VLAN - 2960 switch
Hello, We have a small network (/28 mask) with two PC's and manually configured IP's. PC's are connected to the 2960 switch on two VLAN ports to allow only two PC's at a time on this VLAN. This switch...
2
2
 
SharePoint Developer looking for work
I am software developer looking for freelance work, my skill sets: .NET TECHNOLOGY SharePoint 2010 MOSS 2007 .NET( / C# / VB, ASP (VBScript & Javascript), SQL Server, Access (VBA), Excel (VBA), Oracle...
4
4
 
Changing "N" to "G" to Have Older Adapter Connect
I have a USB "G" adapter that i want to use on my network with an "N" router. how do I change the router so the adapter will connect? Thanks
1
1
 
Looking to buy all used Cisco and other networking and IT hardware!!
Hello, Please let me know what you have available or coming out on your next sched= uled decommission and I can tell you what it's worth. CISCO, IBM, HP,DELL,= AVAYA, FOUNDRY, JUNIPER, NETAPP,...
1
1
 
New To Cisco Router
Hello everyone, I`m new to Cisco router and networking . So , I want guidance on how to start my career in field of networking.I would be very grateful if you would mention about websites.
3
3
 
AutoQoS and multilink PPP
I'm studying AutoQoS and I'm told that for links which speed is lower than 768 kbps AutoQoS may configure multilink PPP. No other expanation is given (as usual in many cases with CiscoPress books). My...
1
1
 
online router laboratory
where online can one find a laboratory or online router laboratories for practicing and simulating router connection sessions for both interdomain and intradomain router setups, esp. where one is...
1
1
 
LPI mode for 1000Base-T
Hi, Is someone will be interrested by this question ? Is the LPI mode always symmetrical in 1000Base-T ? I know there was many discussions before the 802.3az was published, at the end of 2010. Best...
 
sh glbp [brief]
Hi there, is there anyone who can explain the output of the command in the subject? I don't know why it looks not consistent across the memebers partecipating in the GLBP group. Especially the state...
3
3