Latest threads in Cisco Systemsshow only best voted threads
| Subject | Author | Posted | Replies | |
|---|---|---|---|---|
|
|
Traffic Shaping
Dear All, I need to configure traffic shaping on the internet router for my company , I want to allow specific hosts to share specific limit of internet bandwidth howver i have configured policy-map...
2
|
13 years ago
|
2 | |
|
|
IP Inspection
The 2611XL is supposed to be able to forward 20k pps. Even with small packets, that's still over 10 Mbps so I thought it would make a suitable firewall for a school with about 300 students and a...
9
|
13 years ago
|
9 | |
|
|
c3560 port configuration
How need I configure port on c3560 for WLC 5508, ACS Express and some LWAP. I need layer 2 wpa2+AES+802.1x authorization users are in ACS Radius database. thx
—
|
13 years ago
|
— | |
|
|
VPN router
I would like to purchase a router which connects to an internet modem via Ethernet (they all do I believe) and provides 802.11 secured NAT access to workstations behind it. This is for a home network....
3
|
13 years ago
|
3 | |
|
|
WRT610N
I have a WRT610N running 1.00.02 B10. My Dell Studio XPS has a built in Intel 5300 which used to "see" the router's 5GHz SSID but no longer does. I tried upgrading the 5300 driver to 13.2.1.5 (from...
—
|
13 years ago
|
— | |
|
|
NAT Two External Addresses to One Internal Address
Is it possible to NAT two external addresses to one internal address? If it is possible, is it good practice to do so? If it is not good practice to do so, can you point me to documentation explaining...
2
|
13 years ago
|
2 | |
|
|
Inconsistent Subnet Mask
Yes to reach R3 (10.1.1.6), R1 (10.1.1.1) will simply ARP for 10.1.1.6. By default on Cisco Proxy ARP is enabled so unless it has been turned off with no ip proxy-arp, R2 will respond with it's MAC...
4
|
13 years ago
|
4 | |
|
|
DSL stats
where can i find a detailed explantion of the DLS values LOSs ESs LOFs LPRs noise margin Line attenuation What they are and how the effect the ADSL connection many thanks
—
|
13 years ago
|
— | |
|
|
installing a VMWare ESXi connected to a Cisco 6500 at Gigabit?
Hello, I have been trying to place a VMWare ESXi Server on a portchannel port connected at Gigabit. The Server is a IBM eSeries, with 2 Gigabit Ethernet, and is connected to a Cisco 6500 with a 48...
3
|
13 years ago
|
3 | |
|
|
7200VXR - NPE-G2 memory
I'm looking into getting a NPE-G2 engine for our 7204 and upgrading to 2GB of memory. Does anyone have the memory upgrade? Is there any real reason to upgrade from the 1GB default to 2GB?
1
|
13 years ago
|
1 | |
|
|
802.11
im looking to use the Cisco Wireless LAN controller 2106 in a small office What would you recomend as Access points to go with this controller Its being used in a small office with about 25 people i...
1
|
13 years ago
|
1 | |
|
|
WLC 5508, ACS Express, AP 1142 and switch 3560E problem
All devices are in some VLAN 1 (temporaly). Ping works good. WLC gives Web auth for WLAN clients. But Radius on ACS not authorized the users. When I put login and password in local user database on...
—
|
13 years ago
|
— | |
|
|
additional web-auth authorization
My hardware: WLC 5508, ASC express, some AP 1142N K9 lightweight, switch 3560E I have L3 web auth authorization for WLAN clients, save in ASC radius user database. How extend this authorization method...
1
|
13 years ago
|
1 | |
|
|
WRT120n - negative reviews
>guess the newer Linksys (cisco) stuff is trashed - bad - grew up on the Cisco 2501 and later the WRT54xx at home
4
|
13 years ago
|
4 | |
|
|
BGP Load Sharing
Can someone give me a good generic way to load share BGP outbound. I have three connections a 40Mb/s; 20Mb/s; and a 20Mb/s connection. This is currently being done thought PBR. I have a /21 of...
6
|
13 years ago
|
6 |