Latest threads in Cisco Systemsshow only best voted threads

Subject Author Posted Replies
 
How to configure an ntp client
Here is a really good video on how to configure an ntp client on a Cisco router. http://certificationchat.com/content/45-how-configure-ntp-client.html
2
2
 
Cisco Easy VPN connects, but can't access remote LAN
I have Cisco Easy VPN setup on a SR520 router with IOS Version 12.4(20)T6. = The client computer is running Linux using vpnc 0.5.3 I'm able to establish the vpn connection, but can'= t ping the SR520...
13
13
 
redistribute and distribute-list
Hi folks, I'd like to know if the distribute-list is used also in preventing routing loops when redistributing from one routing domain to another another and when of course there more than one points...
11
11
 
Memory Upgrade for Cisco ASA5505
As many know, upgrading an ASA5505 to run firmware 8.4 causes older generat= ion 5505s to exhaust most or all of the default 256MB of configured memory. For those who, like me, don't want to spend...
 
Version 15.1(4)M4 outgoing byte count wrong
In IOS Version 15.1(4)M4 running on an 1811 the output byte count appears to be wrong on Virtual-Access interfaces for L2TP/IPsec. Virtual-Access2 is up, line protocol is up Hardware is Virtual Access...
4
4
 
UCS Network Consulting Engineer
Hi Partners, Hope you are doing well! Please let me know if you have any suitable consultant available for the be= low requirement. UCS Network Consulting Engineer Locations: St Louis, MO Duration :...
 
Cisco 870 Dialer issue
Hi, I have a HQ site able to bring up a Dialer connection to a remote site (Site-BB). It also works in reverse i.e. Site-BB can make the connection into HQ. Now I have a requirement to get a 3rd site...
 
Virtual links OSPF from one area to the backbone through two differents areas.
Hi folks, hope this is the right place to post my question. I'll try to be as concise as I can. I'm studying OSPF with dynamips/IOS and I have read many sources. So far I was told that virtual links...
4
4
 
Fixed address for vpdn users
I have configured a vpdn for l2tp/IPsec dialin users on an 1811. An "ip local pool" is used (in the Virtual-Template) to assign an IP address to the caller. I would prefer if each username had a fixed...
2
2
 
Electrician in New York, landscape lighting Nyc
A New York electrician can repair or replace circuit breakers, cables, fuses, switches or almost any electronic and electrical parts found around your house or apartment.
1
1
 
Anyone has 3700 with WIC1-ADSL ?
Hello I would like to ask any of you if: Cisco 3700 + WIC ADSL IOS 12.4 In the int atm0/0 (internal WIC slot of the 3700) what is the maximum value that you can set in clock-rate AAL5 ? C2600 has...
5
5
 
Questions about Networking
Hey, this is Mike. I'm stumped on some questions I have. The first question I have is , =10 Assume you are connected via serial console to a Cisco 2600 with a default config. You have been assigned...
1
1
 
Mac to VLAN mapping on Cisco switches
Hello, We are looking at ways to ease management of VLANs, and secure on basis of MAC address (yes I know, easily spoofed). After much googling, it seems that: - 802.1x has the potential to do what we...
1
1
 
QOS management on 2960 lan-lite switches
Dear all, one of my customers is starting to migrate his voice infrastructure to a solution based on Cisco UCM and Cisco VOIP phones. The access switches he is currently using are all Cisco 2960 with...
 
PBR problem
Dear All, i have a problem on configuring a PBR to let a server use as next hop a remote site connected by a GRE tunnel. The layout is: LAN ---- (vlan1) Router1 (Tunnel624)...